AM29DL324GB-70EI Spansion Inc., AM29DL324GB-70EI Datasheet - Page 21
![no-image](/images/manufacturer_photos/0/6/621/spansion_inc__sml.jpg)
AM29DL324GB-70EI
Manufacturer Part Number
AM29DL324GB-70EI
Description
Manufacturer
Spansion Inc.
Datasheet
1.AM29DL324GB-70EI.pdf
(58 pages)
Specifications of AM29DL324GB-70EI
Cell Type
NOR
Density
32Mb
Access Time (max)
70ns
Interface Type
Parallel
Boot Type
Bottom
Address Bus
22/21Bit
Operating Supply Voltage (typ)
3/3.3V
Operating Temp Range
-40C to 85C
Package Type
TSOP
Program/erase Volt (typ)
3/8.5 to 9.5V
Sync/async
Asynchronous
Operating Temperature Classification
Industrial
Operating Supply Voltage (min)
2.7V
Operating Supply Voltage (max)
3.6V
Word Size
8/16Bit
Number Of Words
4M/2M
Supply Current
16mA
Mounting
Surface Mount
Pin Count
48
Lead Free Status / Rohs Status
Not Compliant
It is possible to determine whether a sector is pro-
tected or unprotected. See the Autoselect Mode sec-
tion for details.
Write Protect (WP#)
The Write Protect function provides a hardware
method of protecting certain boot sectors without
using V
WP#/ACC pin.
If the system asserts V
vice disables program and erase functions in the two
“outermost” 8 Kbyte boot sectors independently of
whether those sectors were protected or unprotected
using the method described in “Sector/Sector Block
Protection and Unprotection”. The two outermost 8
Kbyte boot sectors are the two sectors containing the
lowest addresses in a bottom-boot-configured device,
or the two sectors containing the highest addresses in
a top-boot-configured device.
If the system asserts V
vice reverts to whether the two outermost 8K Byte
boot sectors were last set to be protected or unpro-
tected. That is, sector protection or unprotection for
these two sectors depends on whether they were last
protected or unprotected using the method described
in “Sector/Sector Block Protection and Unprotection”.
Note that the WP#/ACC pin must not be left floating or
unconnected; inconsistent behavior of the device may
result.
December 4, 2006 25686B10
ID
. This function is one of two provided by the
IH
IL
on the WP#/ACC pin, the de-
on the WP#/ACC pin, the de-
D A T A
Am29DL32xG
S H E E T
Temporary Sector Unprotect
(Note: For the following discussion, the term “sector”
applies to both sectors and sector blocks. A sector
block consists of two or more adjacent sectors that are
protected or unprotected at the same time (see Tables
8 and 9).
This feature allows temporary unprotection of previ-
ously protected sectors to change data in-system. The
Sector Unprotect mode is activated by setting the RE-
SET# pin to V
merly protected sectors can be programmed or erased
by selecting the sector addresses. Once V
moved from the RESET# pin, all the previously pro-
tected sectors are protected again. Figure 1 shows the
algorithm, and Figure 24 shows the timing diagrams,
for this feature.
Notes:
1. All protected sectors unprotected (If WP#/ACC = V
2. All previously protected sectors are protected once
Figure 1. Temporary Sector Unprotect Operation
outermost boot sectors will remain protected).
again.
ID
(8.5 V – 12.5 V). During this mode, for-
Unprotect Completed
Program Operations
Temporary Sector
Perform Erase or
RESET# = V
RESET# = V
(Note 1)
(Note 2)
START
ID
IH
ID
is re-
IL
,
19