S29GL064A90TFIR4 Spansion Inc., S29GL064A90TFIR4 Datasheet - Page 52

• Manufacturer Part Number: S29GL064A90TFIR4
• Manufacturer: Spansion Inc.

Specifications of S29GL064A90TFIR4

• Cell Type: NOR
• Density: 64Mb
• Access Time (max): 90ns
• Interface Type: Parallel
• Boot Type: Bottom
• Address Bus: 23/22Bit
• Operating Supply Voltage (typ): 3/3.3V
• Operating Temp Range: -40C to 85C
• Package Type: TSOP
• Sync/async: Asynchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (max): 3.6V
• Word Size: 8/16Bit
• Number Of Words: 8M/4M
• Supply Current: 50mA
• Mounting: Surface Mount
• Pin Count: 48
• Lead Free Status / Rohs Status: Compliant

9.
9.1
9.2
52
Command Definitions
Reading Array Data
Reset Command
Writing specific address and data commands or sequences into the command register initiates device
operations.
Writing incorrect address and data values or writing them in the improper sequence may place the device in
an unknown state. A reset command is then required to return the device to reading array data.
All addresses are latched on the falling edge of WE# or CE#, whichever happens later. All data is latched on
the rising edge of WE# or CE#, whichever happens first. Refer to
diagrams.
The device is automatically set to reading array data after device power-up. No commands are required to
retrieve data. The device is ready to read array data after completing an Embedded Program or Embedded
Erase algorithm.
After the device accepts an Erase Suspend command, the device enters the erase-suspend-read mode, after
which the system can read data from any non-erase-suspended sector. After completing a programming
operation in the Erase Suspend mode, the system may once again read array data with the same exception.
See
The system must issue the reset command to return the device to the read (or erase-suspend-read) mode if
DQ5 goes high during an active program or erase operation, or if the device is in the autoselect mode. See
Reset Command on page 52
See also Requirements for Reading Array Data in
The Read-Only
on page 74
Writing the reset command resets the device to the read or erase-suspend-read mode. Address bits are don’t
cares for this command.
The reset command may be written between the sequence cycles in an erase command sequence before
erasing begins. This resets the device to the read mode. Once erasure begins, however, the device ignores
reset commands until the operation is complete.
The reset command may be written between the sequence cycles in a program command sequence before
programming begins. This resets the device to the read mode. If the program command sequence is written
while the device is in the Erase Suspend mode, writing the reset command returns the device to the erase-
suspend-read mode. Once programming begins, however, the device ignores reset commands until the
operation is complete.
The reset command may be written between the sequence cycles in an autoselect command sequence.
Once in the autoselect mode, the reset command must be written to return to the read mode. If the device
entered the autoselect mode while in the Erase Suspend mode, writing the reset command returns the device
to the erase-suspend-read mode.
If DQ5 goes high during a program or erase operation, writing the reset command returns the device to the
read mode (or erase-suspend-read mode if the device was in Erase Suspend).
Note that if DQ1 goes high during a Write Buffer Programming operation, the system must write the Write-to-
Buffer-Abort Reset command sequence to reset the device for the next operation.
Erase Suspend/Erase Resume Commands on page 60
Table 10.2 on page 61
shows the timing diagram.
Operations–AC Characteristics on page 72
for more information.
and
Table 10.1 on page 62
S29GL-A
D a t a
Device Bus Operations on page 22
S h e e t
provide the read parameters, and
for more information.
define the valid register command sequences.
AC Characteristics on page 72
S29GL-A_00_A12 May 21, 2008
for more information.
Figure 16.2
for timing