MICRF002BM TR Micrel Inc, MICRF002BM TR Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/4/434/micrel_inc_sml.jpg)
MICRF002BM TR
Manufacturer Part Number
MICRF002BM TR
Description
Manufacturer
Micrel Inc
Datasheet
1.MICRF002BM_TR.pdf
(17 pages)
Specifications of MICRF002BM TR
Operating Band Frequency
300 to 440MHz
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Operating Temperature Classification
Industrial
Modulation Type
ASK/OOK
Product Depth (mm)
3.94mm
Product Height (mm)
1.48mm
Product Length (mm)
9.93mm
Operating Supply Voltage (min)
4.75V
Operating Supply Voltage (typ)
5V
Operating Supply Voltage (max)
5.5V
Lead Free Status / Rohs Status
Not Compliant
MICRF002, allowing the device to operate in applications
where
misalignment may exist. The transmit frequency may vary
up to ±0.5% over initial tolerance, aging, and temperature.
In sweep-mode a band approximately 1.5% around the
nominal transmit frequency is captured. The transmitter
may drift up to ±0.5% without the need to retune the
receiver and without impacting system performance.
The swept-LO technique does not affect the IF bandwidth,
therefore noise performance is not degraded relative to
fixed-mode. The IF bandwidth is 430kHz whether the
device is operating in fixed- or sweep-mode. Due to
limitations imposed by the LO sweeping process, the upper
limit on data rate in sweep mode is approximately 5.0kbps.
Similar performance is not currently available with
crystalbased superheterodyne receivers which can operate
only with SAW- or crystal-based transmitters. In sweep-
mode, a range reduction will occur in installations where
there is a strong interferer in the swept RF band. This is
because the process indiscriminately includes all signals
within the sweep range. An MICRF002 may be used in
place of a superregenerative receiver in most applications.
Step 2: Selecting the Reference Oscillator
All timing and tuning operations on the MICRF002 are
derived from the internal Colpitts reference oscillator.
Timing and tuning is controlled through the REFOSC pin in
one of three ways:
The specific reference frequency required is related to the
system transmit frequency and to the operating mode of
the receiver as set by the SWEN pin.
Crystal or Ceramic Resonator Selection
Do not use resonators with integral capacitors since
capacitors are included in the IC, also care should be taken
to ensure low ESR capacitors are selected. Application Hint
34 and Application Hint 35 provide additional information
and recommended sources for crystals and resonators.
If operating in fixed-mode, a crystal is recommended. In
sweep-mode either a crystal or ceramic resonator may be
used. When a crystal of ceramic resonator is used the
minimum voltage is 300mV
signal it should be AC-coupled and limited to the operating
range of 0.1V
Selecting Reference Oscillator Frequency f
Mode)
As with any superheterodyne receiver, the mixing
between the internal LO (local oscillator) frequency f
the incoming transmit frequency f
IF center frequency. Equation 1 may be used to compute
Micrel, Inc.
July 2008
1. Connect a ceramic resonator
2. Connect a crystal
3. Drive this pin with an external timing signal
significant
PP
to 1.5V
PP
.
transmitter-receiver
PP
. If using an externally applied
TX
ideally must equal the
T
frequency
(Fixed-
LO
and
8
the appropriate f
Frequencies f
f
mixing” and “low-side mixing”. High-side mixing results in
an image frequency above the frequency of interest and
low-side mixing results in a frequency below.
After choosing one of the two acceptable values of f
Equation 2 to compute the reference oscillator frequency f
Frequency f
REFOSC on the MICRF002. Four-decimal-place accuracy
on the frequency is generally adequate. The following table
identifies f
the MICRF002 is operated in fixed mode.
Selecting REFOSC Frequency f
Selection of the reference oscillator frequency f
mode is much simpler than in fixed mode due to the LO
sweeping process. Also, accuracy requirements of the
frequency reference component are significantly relaxed.
In sweep-mode, f
In sweep-mode a reference oscillator with frequency
accurate to two-decimal-places is generally adequate. A
crystal may be used and may be necessary in some cases
if the transmit frequency is particularly imprecise.
Table 3. Sweep-Mode Recommended Reference Oscillator
LO
Table 2. Fixed-Mode Recommended Reference Oscillator
Transmit Frequency f
Transmit Frequency f
exist for any given f
(1)
(2)
(3)
433.92MHz
433.92MHz
Values for Typical Transmit Frequencies
Values for Typical Transmit Frequencies
T
315MHz
390MHz
418MHz
315MHz
390MHz
418MHz
T
for some common transmit frequencies when
is in MHz. Connect a crystal of frequency f
TX
and f
LO
T
f
f
f
LO
T
T
is given by Equation 3:
for a given f
=
=
(high-side mixing)
LO
=
64.5
64.25
f
f
are in MHz. Note that two values of
LO
f
TX
LO
TX
TX
TX
±
, distinguished as “high-side
⎛
⎜ ⎜
⎝
0.86
TX
:
Reference Oscillator
Reference Oscillator
T
315
f
(Sweep-Mode)
TX
Frequency f
Frequency f
4.8970MHz
6.0630MHz
6.4983MHz
6.7458MHz
MICRF002/RF022
⎞
⎟ ⎟
⎠
4.88MHz
6.05MHz
6.48MHz
6.73MHz
M9999-070808
T
in sweep-
T
T
LO
, use
T
to
T
: