NOIL1SN3000A-GDC ON Semiconductor, NOIL1SN3000A-GDC Datasheet - Page 23
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
NOIL1SN3000A-GDC
Manufacturer Part Number
NOIL1SN3000A-GDC
Description
Manufacturer
ON Semiconductor
Datasheet
1.NOIL1SN3000A-GDC.pdf
(58 pages)
Specifications of NOIL1SN3000A-GDC
Lead Free Status / Rohs Status
Supplier Unconfirmed
Y_end (b0001001 / d9 and b0001010 / d10)
row to readout. Because a row address is 11-bit wide, the
Y_end address is split over two registers: Y_end<10:8> and
Y_end<7:0>. Y_end<10:8> contains 3 MSBs of the 11-bit
address, and Y_end<7:0> contains 8 LSBs of the address.
Y_end<10:0> must be larger than Y_start<10:0> and not
larger than 1709.
X_start (b0001011 / d11)
readout. Readout in X starts only at odd kernel positions. As
a result, possible start positions are 64 columns (2 kernels)
separated from each other.
Table 24. Y_END REGISTER
Table 25. X_START REGISTER
Y_end<7:0> (b0001001 / d9)
Y_end<10:8> (b0001010 / d10): Bits<7:3> are ignored
On startup
The Y_end register contains the row address of the last
The X_start register contains the start position for the X
Bits <7:5> are ignored.
Bit<4:0>
On startup
On startup
00000
00001
Bit<2:0>
Value
11010
Value
X readout starts with the first kernel (column 0)
X readout starts with the third kernel
(column 64)
X readout starts with the fifty third kernel
(column 1664)
00000
10101101
00000110
Effect
Effect
http://onsemi.com
23
Training (b0001100 / d12)
modes. Bits <7:2> are ignored.
•
•
•
Black_ref (b0001101 / d13)
the ADC. The analog output of the DAC corresponds with
the all zero code of the ADC. The DAC has an 8-bit
resolution and outputs between VAA2V5 and 0 V. This
means that the step size corresponds with about 9.8 mV. The
DAC itself outputs between VAA2V5 and 0 V, but the
buffering circuit that follows after the DAC clips the voltage
close to ground and supply.
Table 26. TRAINING REGISTER
Table 27. BLACK_REF REGISTER
Training_en, bit<0>
Bypass_mode, bit<1>
Analog_out_en, bit<2>
This register allows switching between different readout
This register controls the DAC that sets the dark level for
Training_en, bit<0>. In bypass mode, this bit is
evaluated and determines if the training pattern or test
image is transmitted.
Bypass_mode, bit<1>. This bit allows the sensor to
switch between normal readout of an image and readout
for testing or training purposes.
Analog_out_en, bit<2>.This bit activates the analog
output of the sensor. The analog value of
column<1696> is brought to the output.
On startup
On startup
On startup
On startup
00000000
00000001
11111111
Value
Value
…
1
0
0
1
0
1
In bypass mode, the training pattern is
transmitted
In bypass mode, the test image is transmitted
0
Normal readout of captured images
Bypass mode readout. The content of register
TRAINING_EN is evaluated.
0
Analog output disabled
Analog output enabled
0
Output of DAC is VAA2V5
Output of DAC is VAA2V5–9.8 mV
Output of DAC is 0 V
01100110
Effect
Effect