MAX378CPE Maxim Integrated Products, MAX378CPE Datasheet
MAX378CPE
Specifications of MAX378CPE
Available stocks
Related parts for MAX378CPE
MAX378CPE Summary of contents
Page 1
... Fault Conditions No Increase in Supply Currents Due to Fault Conditions Latchup-Proof Construction Operates from ±4.5V to ±18V Supplies All Digital Inputs are TTL and CMOS Compatible Low-Power Monolithic CMOS Design ______________Ordering Information PART MAX378CPE MAX378CWG MAX378CJE MAX378C/D MAX378EPE MAX378EWG MAX378EJE MAX378MJE MAX378MLP Ordering Information continued at end of data sheet. ...
Page 2
High-Voltage, Fault-Protected Analog Multiplexers ABSOLUTE MAXIMUM RATINGS Voltage between Supply Pins ..............................................+44V V+ to Ground ...................................................................+22V V- to Ground......................................................................-22V Digital Input Overvoltage: { V+......................................................................+ ........................................................................-4V Analog Input with Multiplexer Power On..............................±65V { } Recommended ...
Page 3
ELECTRICAL CHARACTERISTICS (continued) (V+ = +15V -15V; V (Logic Level High) = +2.4V PARAMETER SYMBOL DYNAMIC Access Time t A Break-Before-Make Delay OFF (Figure 2) Enable Delay (ON) t ON(EN) Enable Delay (OFF) ...
Page 4
High-Voltage, Fault-Protected Analog Multiplexers __________________________________________Typical Operating Characteristics INPUT LEAKAGE vs. INPUT VOLTAGE WITH 100 10 1 OPERATING RANGE 100n 10n 1n 100p 10p -100 - 100 V (V) IN NOTE: Typical R ...
Page 5
MAX358 3.0V AH ADDRESS DRIVE ( OUTPUT 50% 50% t OPEN Figure 2. Break-Before-Make Delay (t ) OPEN MAX378 3.0V AH ENABLE DRIVE 50% 0V 90% OUTPUT 90% t ON(EN) t OFF(EN) Figure ...
Page 6
High-Voltage, Fault-Protected Analog Multiplexers Truth Table—MAX378 ...
Page 7
Input switching, however, must be done with a fault- protected MAX378 multiplexer, to provide the level of protection and isolation required with most data acqui- sition inputs. Since external signal sources may contin supply voltage when the multiplexer ...
Page 8
High-Voltage, Fault-Protected Analog Multiplexers to-source voltage. The P-channel device (Q2), howev- er, has +60V V and is turned off, thereby preventing GS the input signal from reaching the output. If the input voltage is +60V, Q1 has a negative V ...
Page 9
Table 1b. MAX379 Charge Injection Injected Charge Supply Analog Voltage Input Level Out A Out B +1.7V +105pC +107pC ±5V 0V +73pC +74pC -1.7V +48pC +50pC +5V +215pC +220pC ±10V 0V +135pC +139pC -5V +62pC +63pC +10V +525pC +530pC ±15V ...
Page 10
High-Voltage, Fault-Protected Analog Multiplexers _____________________________________________Pin Configurations (continued N. N. MAX378 IN1 6 19 IN2 7 18 IN3 8 17 IN4 N.C. 14 ...
Page 11
Information (continued) PART TEMP. RANGE PIN-PACKAGE MAX379CPE 0°C to +70°C 16 Plastic DIP MAX379CWG 0°C to +70°C 24 Wide SO MAX379CJE 0°C to +70°C 16 CERDIP MAX379C/D 0°C to +70°C Dice** MAX379EPE -40°C to +85°C 16 Plastic DIP MAX379EWG ...
Page 12
... Maxim reserves the right to change the circuitry and specifications without notice at any time. implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600 12 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600 © ...