MAX4571CWI+ Maxim Integrated Products, MAX4571CWI+ Datasheet - Page 6

• Manufacturer Part Number: MAX4571CWI+
• Description: IC AUDIO/VIDEO SWITCH 11 20SOIC
• Manufacturer: Maxim Integrated Products

Specifications of MAX4571CWI+

• Function: Audio/Video Switch
• Circuit: 11P11T - NO
• On-state Resistance: 35 Ohm
• Voltage Supply Source: Single Supply
• Voltage - Supply, Single/dual (±): 2.7 V ~ 5.25 V
• Current - Supply: 6µA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 20-SOIC (0.300", 7.50mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Serially Controlled, Clickless
Audio/Video Switches
Note 2:
Note 3:
Note 4:
Note 5:
Note 6:
Note 7:
Note 8:
Note 9:
Note 10: Leakage testing for single-supply operation is guaranteed by testing with a single +5.25V supply.
Note 11: C
Note 12: Typical values are for MAX4573/MAX4574 devices.
(V+ = +5V, T
6
5.1
5.0
4.9
4.8
4.7
4.6
4.5
_______________________________________________________________________________________
50
45
40
35
30
25
20
-40
0
SUPPLY CURRENT vs. TEMPERATURE
The algebraic convention is used in this data sheet; the most negative value is shown in the minimum column.
Guaranteed by design. Not subject to production testing.
∆R
Resistance flatness is defined as the difference between the maximum and minimum on-resistance values, as measured
over the specified analog signal range.
Leakage parameters are 100% tested at maximum rated temperature, and guaranteed by correlation at T
Off-isolation = 20 log [V
All timing is measured from the rising clock edge of the ACK bit for 2-wire, and from the rising edge of CS for 3-wire. Turn-
off time is defined at the output of the switch for a 0.5V change, tested with a 300Ω load to ground. Turn-on time is mea-
sured with a 5kΩ load resistor to GND. All timing is shown with respect to 20% V+ and 70% V+, unless otherwise noted.
Supply current can be as high as 2mA per switch during switch transitions in the clickless mode, corresponding to a 28mA
total supply transient current requirement.
-20
b
ON
A
ON-RESISTANCE vs. V
= capacitance of one bus line in pF. Tested with C
1
= +25°C, unless otherwise noted.)
= R
V+ = 2.7V
TEMPERATURE (°C)
0
ON(MAX)
2
V
COM
20
(V)
3
40
- R
V+ = 3.3V
V+ = 5.0V
ON(MIN)
COM
60
COM
4
_ / V
80
.
5
NO
_ _ ], V
32
30
28
26
24
22
20
18
-1
-2
-3
3
2
1
0
0
0
COM
T
CHARGE INJECTION vs. V
_ = output, V
A
V
= +70°C
1
1
COM
ON-RESISTANCE vs.
AND TEMPERATURE
b
T
2
2
T
= 400pF.
V
V
A
A
T
COM
COM
= -40°C
A
= +25°C
= +85°C
NO
(V)
(V)
Typical Operating Characteristics
3
3
_ _ = input to off switch.
COM
4
4
5
5
0.001
0.01
100
600
500
400
300
200
100
0.1
10
1
0
-40
-40
LEAKAGE CURRENT vs. TEMPERATURE
ON/OFF TIME vs. TEMPERATURE
-20
-20
t
ON
, V+ = 3V
TEMPERATURE (°C)
TEMPERATURE (°C)
0
0
(HARD MODE)
20
20
COM_ OFF
A
= +25°C.
t
t
OFF
ON
40
40
, V+ = 5V
t
, V+ = 3V
OFF
NO_ _ OFF
, V+ = 5V
NO_ _ ON
60
60
80
80