MCP3901A0-E/ML Microchip Technology, MCP3901A0-E/ML Datasheet - Page 5

• Manufacturer Part Number: MCP3901A0-E/ML
• Description: IC AFE 24BIT 64KSPS 2CH 20QFN
• Manufacturer: Microchip Technology
• Series: -r

Specifications of MCP3901A0-E/ML

• Number Of Bits: 24
• Number Of Channels: 2
• Power (watts): -
• Voltage - Supply, Analog: 4.5 V ~ 5.5 V
• Voltage - Supply, Digital: 2.7 V ~ 5.5 V
• Package / Case: 20-VFQFN Exposed Pad
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

ELECTRICAL CHARACTERISTICS (CONTINUED)
© 2011 Microchip Technology Inc.
Electrical Specifications: Unless otherwise indicated, AV
MCLK = 4 MHz; PRESCALE = 1; OSR = 64; GAIN = 1; Dithering OFF; V
AC Power Supply Rejection
DC Power Supply Rejection
DC Common-Mode Rejection
Ratio
Oscillator Input
Master Clock Frequency Range
Power Specifications
Operating Voltage, Analog
Operating Voltage, Digital
Power On Reset Threshold
Operating Current, Analog
(Note
Operating Current, Digital
Shutdown Current, Analog
Shutdown Current, Digital
Note 1:
(Note
4)
2:
3:
4:
5:
6:
7:
8:
Parameters
This specification implies that the ADC output is valid over this entire differential range and that there is no
distortion or instability across this input range. Dynamic performance is specified at -0.5 dB below the
maximum signal range, V
See terminology section for definition.
This parameter is established by characterization and not 100% tested.
For these operating currents, the following bit settings apply: SHUTDOWN<1:0> = 00, RESET<1:0> = 00,
VREFEXT = 0, CLKEXT = 0.
For these operating currents, the following Configuration bit settings apply: SHUTDOWN<1:0> = 11,
VREFEXT = 1, CLKEXT = 1.
Applies to all gains. Offset error is dependant on PGA gain setting (see
Outside of this range, the ADC accuracy is not specified. An extended input range of ±6V can be applied
continuously to the part with no risk for damage.
For proper operation and to keep ADC accuracy, AMCLK should always be in the range of 1 to 5 MHz with
BOOST bits off. With BOOST bits on, AMCLK should be in the range of 1 to 8.192 MHz,
AMCLK = MCLK/PRESCALE. When using a crystal, the CLKEXT bit should be equal to ‘0’.
2)
AC PSRR
DC PSRR
IN
Symbol
CMRR
MCLK
I
I
DV
AV
DDS,D
POR
AI
DI
DDS,A
= -0.5 dBFS @ 50/60 Hz = 353 mV
DD
DD
DD
DD
Min
4.5
2.7
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1
DD
= 4.5 to 5.5V, DV
Typical
0.45
0.25
-77
-77
-72
3.6
4.2
4.6
2.1
2.1
3.8
3.8
1.2
—
—
—
—
IN
RMS,
16.384
= -0.5 dBFS = 333 mV
Max
0.45
5.5
5.5
2.8
3.3
5.6
1.0
1.6
—
—
—
—
—
7
1
1
DD
V
REF
= 2.7 to 5.5V; -40°C < T
Figure 2-19
= 2.4V.
Units
MHz
mA
mA
mA
mA
mA
mA
mA
dB
dB
dB
µA
µA
V
V
V
for typical values).
MCP3901
AV
1 V
AV
5.5V
V
+1V
(Note
(Note
-40°C < T
(Note
BOOST<1:0> = 00
-40°C < T
BOOST<1:0> = 00
BOOST<1:0> = 11
-40°C < T
BOOST<1:0> = 11
DV
MCLK = 4 MHz
DV
MCLK = 4 MHz
DV
MCLK = 8.192 MHz
AV
DV
CM
RMS
DD
DD
DD
DD
DD
DD
DD
PP
varies from -1V to
pin only
and DV
and DV
= 5V,
= 2.7V,
= 5V,
pin only
Conditions
@ 50/60 Hz
8)
3)
3)
@ 50/60 Hz
DS22192D-page 5
A
A
A
A
< +85°C,
< 125°C,
< 125°C,
< 125°C,
DD
DD
(Note
(Note
= 5V +
= 4.5 to
5)
5)