SI3220-BQ Silicon Laboratories Inc, SI3220-BQ Datasheet - Page 37
![IC SLIC/CODEC DUAL-CH 64TQFP](/photos/16/12/161288/tqfp-64_sml.jpg)
SI3220-BQ
Manufacturer Part Number
SI3220-BQ
Description
IC SLIC/CODEC DUAL-CH 64TQFP
Manufacturer
Silicon Laboratories Inc
Series
ProSLIC®r
Specifications of SI3220-BQ
Package / Case
*
Function
Subscriber Line Interface Concept (SLIC), CODEC
Interface
GCI, PCM, SPI
Number Of Circuits
2
Voltage - Supply
3.3V, 5V
Current - Supply
65mA
Power (watts)
941mW
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Includes
Battery Switching, BORSCHT Functions, DTMF Generation and Decoding, FSK Tone Generation, Modem and Fax Tone Detection
Product
Telecom
Supply Voltage (min)
3.13 V
Supply Current
22 mA
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Number Of Channels
2
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
SI3220-BQ
Manufacturer:
TONTEK
Quantity:
12 000
Company:
Part Number:
SI3220-BQ
Manufacturer:
Silicon Laboratories Inc
Quantity:
10 000
3.6. Linefeed Calibration
An internal calibration algorithm corrects for internal and
external component errors. The calibration is initiated by
setting the CAL register bit. This bit automatically resets
upon completion of the calibration cycle.
A calibration should be executed following system
powerup. Upon release of the chip reset, the chipset will
be in the open state, and calibration may be initiated.
Only one calibration should be necessary if the system
remains powered up.
To optimize Dual ProSLIC performance, the calibration
routine in “AN58: Si3220/Si3225 Programmer’s Guide”
should be followed.
3.7. Loop Voltage and Current Monitoring
The Dual ProSLIC chipset continuously monitors the
TIP and RING voltages and currents. These values are
available in registers. An internal 8-bit A/D converter
samples the measured voltages and currents from the
analog sense circuitry and translates them into the
digital domain. The A/D updates the samples at an
800 Hz rate for all inputs except VRNGNG and
IRNGNG, which are sampled at 8 kHz to provide higher
resolution for zero-crossing detection in external ringing
applications. Two derived values, the loop voltage
-20 V
-40 V
-48 V
-80 V
-0 V
V
0 mA
RING
VOC DELTA
Figure 17. Ground Start V
VOCHTH
Rev. 1.3
VOCLTH
(V
For ground start operation, the values reported are
V
Table 21 lists the register set associated with the loop
monitoring functions.
The Dual ProSLIC chipsets also include the ability to
perform loop diagnostic functions as outlined in "3.32.2.
Line Test and Diagnostics" on page 96.
3.8. Power Monitoring and Power Fault
The Dual ProSLIC line monitoring functions can be
used to protect the high-voltage circuitry against
excessive power dissipation and thermal overload
conditions. The Dual ProSLIC devices can prevent
thermal overloads by regulating the total power inside
the Si3200/2 or in each of the external bipolar
transistors (if using a discrete linefeed circuit). The DSP
engine performs all power calculations and provides the
ability to automatically transition the device into the
OPEN state and generate a power alarm interrupt when
excessive power is detected. Table 22 on page 41
describes the register and RAM locations used for
power monitoring.
RING
TIP
RING
– V
Detection
/I
and the current flowing in the RING lead.
RING
RING
Si3220/25 Si3200/02
) and the loop current are also reported.
Behavior
24 mA
I
RING
37