NS16C2552TVSX/NOPB National Semiconductor, NS16C2552TVSX/NOPB Datasheet - Page 5
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
NS16C2552TVSX/NOPB
Manufacturer Part Number
NS16C2552TVSX/NOPB
Description
IC UART DUAL 16BYTE 48-TQFP
Manufacturer
National Semiconductor
Datasheet
1.NS16C2552TVSXNOPB.pdf
(44 pages)
Specifications of NS16C2552TVSX/NOPB
Features
Programmable
Number Of Channels
2, DUART
Fifo's
16 Byte
Voltage - Supply
2.97 V ~ 5.5 V
With Auto Flow Control
Yes
With Irda Encoder/decoder
Yes
With Modem Control
Yes
Mounting Type
Surface Mount
Package / Case
48-VFQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
NS16C2552TVSX
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
NS16C2552TVSX/NOPB
Manufacturer:
Texas Instruments
Quantity:
10 000
D7
D6
D5
D4
D3
D2
D1
D0
A2
A1
A0
CS
CHSL
RD
WR
RXRDY1
RXRDY2
Signal
Name
5.0 Pin Descriptions
The NS16C2552/NS16C2752 pins are classified into the fol-
lowing interface categories.
•
•
•
•
Serial channel number (1 or 2) is designated by a numerical
suffix after each pin name. If a numerical suffix (1 or 2) is not
5.1 PARALLEL BUS INTERFACE
Bus Interface
Serial I/O Interface
Clock and Reset
Power supply and Ground pins
Type
IO_Z
O
I
I
I
I
I
PLCC
Pin #
N/A
15
14
10
18
16
24
20
9
8
7
6
5
4
3
2
TQFP
Pin #
48
47
46
45
44
10
13
11
20
15
31
3
2
1
9
4
8
Data Bus:
Data bus comprises eight TRI-STATE input/output lines. The bus provides bidirectional
communications between the UART and the CPU. Data, control words, and status
information are transferred via the D
Register Addresses:
Address signals connected to these 3 inputs select a DUART register for the CPU to read
from or write to during data transfer. Table 1 shows the registers and their addresses. Note
that the state of the Divisor Latch Access Bit (DLAB), which is the most significant bit of the
Line Control Register, affects the selection of certain DUART registers. The DLAB must be
set high by the system software to access the Baud Generator Divisor Latches and the
Alternate Function Register.
Chip Select:
When CS is low, the chip is selected. This enables communication between the DUART
and the CPU. Valid chip select should stabilize according to the t
Channel Select:
CHSL directs the address and data information to the selected serial channel. (Table 1)
1 = channel 1 is selected.
0 = channel 2 is selected.
IO Read:
The register data is placed on the D0 - D7 on the falling edge of RD. The CPU can read
status information or data from the selected DUART register on the rising edge.
IO Write:
On the falling edge of WR, data is placed on the D0 - D7. On the rising edge, the data is
latched into the selected DUART register.
UART Receive-ready: The receiver DMA signaling is available through this pin which is a
seperate pin on the TQFP package, while on the PLCC package it is available through the
MF pins (19, 35). When operating in the FIFO mode, the CPU selects one of two types of
DMA transfer via FCR[3]. When operating in the 16450 Mode, only DMA mode 0 is
available. Mode 0 supports single transfer DMA (and a transfer is usually made between
CPU bus cycles). Mode 1 supports multi-transfer DMA where multiple transfers are made
continuously until the Rx FIFO is empty. Details regarding the active and inactive states of
this signal are described in Section 6.5 FIFO CONTROL REGISTER (FCR) and Section 7.9
DMA OPERATION.
5
associated with the pin name, the information applies to both
channels.
The I/O types are as follows:
Type: I
Type: O
Type: IO_Z
7
-D
Description
0
Data Bus.
Input
Output
TRI-STATE I/O
AW
parameter.
www.national.com