LM4730TA/NOPB National Semiconductor, LM4730TA/NOPB Datasheet - Page 4

• Manufacturer Part Number: LM4730TA/NOPB
• Description: IC AMP AUDIO PWR 14W AB TO220-15
• Manufacturer: National Semiconductor
• Type: Class ABr

Specifications of LM4730TA/NOPB

• Output Type: 2-Channel (Stereo)
• Max Output Power X Channels @ Load: 14W x 2 @ 8 Ohm
• Voltage - Supply: 20 V ~ 50 V, ±10 V ~ 25 V
• Features: Depop, Mute, Short-Circuit and Thermal Protection
• Mounting Type: Through Hole
• Package / Case: TO-220-15 (Bent and Staggered Leads)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: *LM4730TA/NOPB; LM4730TA

www.national.com
Mute
Symbol
V
V
Note 1: All voltages are measured with respect to the ground pin, unless otherwise specified.
Note 2: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions
which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters
where no limit is given. However, the typical value is a good indication of a device's performance.
Note 3: The maximum power dissipation must be de-rated at elevated temperatures and is dictated by T
allowable power dissipation is P
150°C and the typical θ
Note 4: Human body model, 100 pF discharged through a 1.5 kΩ resistor.
Note 5: Machine Model: a 220pF - 240pF discharged through all pins.
Note 6: Typical specifications are sepcified at 25°C and represent the parametric norm.
Note 7: Tested limits are guaranteed to National's AOQL (Average Outgoing Quality Level).
Note 8: Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis.
Note 9: The operating junction temperature maximum is 150°C. However, the instantaneous Safe Operating Area temperature is 250°C.
Note 10: V
differential between V
Note 11: The feedback compensation network limits the bandwidth of the closed-loop response causing the skew rate to be reduced by the high frequency roll-
off. Without feedback compensation the slew rate is typically larger.
Note 12: The LM4730TA package TA15A is a non-isolated package setting the tab of the device and the heat sink to V
mounted to the heat sink using only thermal compound. If a mica washer is used in addition to thermal compound, θ
sink will be electrically isolated from V
IL
IH
-
must have at least -9V at its pin with reference to GND in order for the under-voltage protection circuitry to be disabled. In addition, the voltage
Mute Low Input Voltage
Mute High Input Voltage
+
JC
and V
is 1.5°C/W for the TA15A package . Refer to the Thermal Considerations section for more information.
Parameter
-
must be greater than 14V.
DMAX
= (T
-
.
JMAX
200594 Version 3 Revision 2
-T
A
) / θ
JC
or the number given in the Absolute Maximum Ratings, whichever is lower. For the LM4730, T
Not in Mute Mode (Play)
In Mute Mode
Conditions
Print Date/Time: 2009/10/26 15:41:58
4
JMAX
, θ
JC
, and the ambient temperature T
(Note
Typical
2.0
CS
-
(case to sink) is increased, but the heat
potential when the LM4730TA is directly
6)
LM4730
(Note
Limit
0.8
2.5
8)
7,
Note
A
. The maximum
(Limits)
V (max)
V (min)
Units
JMAX
=