MAX9722AETE+T Maxim Integrated Products, MAX9722AETE+T Datasheet - Page 13

• Manufacturer Part Number: MAX9722AETE+T
• Description: IC AMP AUDIO .13W STER AB 16TQFN
• Manufacturer: Maxim Integrated Products
• Series: DirectDrive™r
• Type: Class ABr

Specifications of MAX9722AETE+T

• Output Type: Headphones, 2-Channel (Stereo)
• Max Output Power X Channels @ Load: 130mW x 2 @ 32 Ohm
• Voltage - Supply: 2.4 V ~ 5.5 V
• Features: Depop, Differential Inputs, Short-Circuit and Thermal Protection, Shutdown
• Mounting Type: Surface Mount
• Package / Case: 16-TQFN Exposed Pad
• Product: General Purpose Audio Amplifiers
• Output Power: 130 mW
• Common Mode Rejection Ratio (min): - 70 dB
• Thd Plus Noise: 0.009 %
• Operating Supply Voltage: 2.4 V to 5.5 V
• Supply Current: 5.5 mA
• Maximum Power Dissipation: 1176 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Input Bias Current (max): 50 nA
• Input Offset Voltage: 0.5 mV
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.4 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: MAX9722AETE+T; MAX9722AETE+TTR

Figure 8. Common-Mode Sense Input Eliminates Ground-Loop
Noise
Figure 9. Common-Mode Noise Rejection
AUDIO
AUDIO
INPUT
RIGHT
INPUT
LEFT
Stereo Headphone Amplifiers with Shutdown
SHDN
5V, Differential Input, DirectDrive, 130mW
______________________________________________________________________________________
MAX9722A
EXAMPLE CONNECTION:
IMPROVEMENT FROM
ADDING MAX9722 WITH
SERIES RESISTANCE
V
AUDIO
V
AUDIO
R
2
R
1
RESISTOR IS
INSERTED
BETWEEN THE
JACK SLEEVE
AND
GND = 9.8Ω
MAX9722A
9.8Ω
•
•
•
9.8Ω RESISTOR ADDS TO HP CROSSTALK, BUT DIFFERENTIAL
SENSING AT THE JACK SLEEVE CORRECTS FOR THIS (ONE CHANNEL
ONLY SHOWN).
CURRENT FLOW (IN SIGNAL CABLE SCREEN) DUE TO V
IS GREATLY REDUCED.
NOISE COMPONENT IN THE RECEIVER OUTPUT IS REDUCED BY 34dB
OVER THE PREVIOUS EXAMPLE WITH THE VALUES SHOWN.
•
•
•
V
0.10Ω RESISTANCE FROM CABLE SCREEN.
0.10Ω RESISTANCE DUE TO GND CABLING AT RECEIVER.
V
THE TWO GNDS.
V
0.1Ω
0.1Ω
NOISE
NOISE
NOISE
When the headphone jack is used as a line out to inter-
face between other equipment (notebooks, desktops,
and stereo receivers), potential differences between
the equipment grounds can create ground loops and
excessive ground-current flow. The MAX9722A’s INR+
and INL+ inputs are connected together to form a com-
mon-mode input that senses and corrects for the differ-
ence between the headphone return and device
ground (see Figure 8). Connect INR+ and INL+ through
a resistive voltage-divider between the headphone jack
return and SGND of the device. For optimum common-
mode rejection, use the same value resistors for R
R
and R
capacitor between SGND and R
Application Circuit). If ground sensing is not required,
connect INR+ and INL+ directly to SGND.
Figure 9 shows a theoretical connection between two
devices, for example, a notebook computer (transmit-
ter, on the left) and an amplifier (receiver, on the right),
REPRESENTS THE POTENTIAL DIFFERENCE BETWEEN
F
, and R
F
0.1Ω
0.1Ω
= 30kΩ. Improve DC CMRR by adding a
2
V
V
V
V
and R
REF_IN
REF_IN
IN
IN
= V
= V
Common-Mode Noise Rejection
GND NOISE COMPONENT IN
OUTPUT = V
GND NOISE COMPONENT IN
OUTPUT = V
AUDIO
AUDIO
= V
= (V
NOISE
IN
NOISE
+ (V
. For the MAX9722B, R
/2
NOISE
x 0.99)
NOISE
NOISE
x 0.98)
/2
/100
NOISE
Common-Mode Sense
2
(see the Typical
IN
= 15kΩ
1
and
13