PS21212 MITSUBISHI, PS21212 Datasheet

no-image

PS21212

Manufacturer Part Number
PS21212
Description
5A power module for transfer-mold type insulated type
Manufacturer
MITSUBISHI
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PS21212
Manufacturer:
MITSUBISHI
Quantity:
50
APPLICATION
AC100V~200V three-phase inverter drive for small power (0.2 kW) motor control.
PS21212
Fig. 1 PACKAGE OUTLINES
INTEGRATED DRIVE, PROTECTION AND SYSTEM CONTROL FUNCTIONS
• For upper-leg IGBT
• For lower-leg IGBT
• Fault signaling : Corresponding to a SC fault (Low-side IGBT) or a UV fault (Low-side supply).
• Input interface : 5V line CMOS/TTL compatible, Schmitt Trigger receiver circuit.
TERMINALS CODE
1. U
2. V
3. V
P1
UFB
P
S
S
: Drive circuit, Control curcuit under-voltage protection (UV), Short circuit protection (SC). (Fig. 3)
: Drive circuit, High voltage isolated high-speed level shifting, Control circuit under-voltage (UV) protection.
4. V
5. V
6. V
Note : Bootstrap supply scheme can be applied (Fig. 2).
UFS
P
P1
MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module>
2- 4.5
MITSUBISHI SEMICONDUCTOR <Dual-In-Line Package Intelligent Power Module>
7. V
8. V
9. W
1
2.8
VFB
VFS
P
2
3
4
22
10. V
11. V
12. V
5
10
6
23
7
P1
PC
WFB
10
8
24
9
13. V
14. V
15. V
10
67
79
10
11 12
25
WFS
N1
NC
13
INTEGRATED POWER FUNCTIONS
600V/5A low-loss 3rd generation IGBT inverter bridge for 3
phase DC-to-AC power conversion (Fig. 2)
Application Motor Ratings : Power : 0.2kW, sinusoidal, PWM
*(Note) : The motor current is assumed to be sinusoidal and
20
14
16. CIN 19. U
17. CFO 20. V
18. Fo
15
16
the peak current value is defined as : l
26
17
18
19
20
21. W
21
N
N
N
TRANSFER-MOLD TYPE
Frequency=15kHz
100% load current : 1.5A (rms)*
150% load current : 2.25A (rms)*,
22. P
23. U
24. V
TRANSFER-MOLD TYPE
PS21212
INSULATED TYPE
INSULATED TYPE
25. W
26. N
PS21212
O
1 minute.
3.8
2
Aug. 1999

Related parts for PS21212

PS21212 Summary of contents

Page 1

... The motor current is assumed to be sinusoidal and the peak current value is defined 10. V 13. V 16. CIN 19 WFS N 11. V 14. V 17. CFO 20 12. V 15. V 18. Fo 21. W WFB NC N PS21212 PS21212 TRANSFER-MOLD TYPE INSULATED TYPE INSULATED TYPE 1 minute 3.8 22. P 25. W 23. U 26. N 24. V Aug. 1999 ...

Page 2

... OFF and a fault signal (Fo) is output. Since the SC fault may be repetitive recommended to stop the system when the Fo signal is received and check the fault Protection Trip Level Collector current waveform PS21212 TRANSFER-MOLD TYPE INSULATED TYPE Bootstrap circuit For detailed description of the boot-strap circuit C4 construction, please C3 contact Mitsubishi Electric (Note 6) DIP-IPM ...

Page 3

... Applied between CIN-V NC Condition 13.5~16.5V, Inverter part 125°C, non-repetitive, less than (Note 2) 60Hz, Sinusoidal minute, connection pins to heat-sink plate Control pins Heat sink boundary Tc Power pins PS21212 TRANSFER-MOLD TYPE INSULATED TYPE Ratings Unit V 450 500 V 600 –20~+150 °C 100°C) however , to in- C 125° ...

Page 4

... CFO– Applied between Applied between according to the following approximate equation : C FO PS21212 TRANSFER-MOLD TYPE INSULATED TYPE Limits Unit Min. Typ. Max. — — 4.0 — — 6.1 °C/W — — 0.067 Limits Unit Min. Typ. Max. — ...

Page 5

... UFB UFS VFB VFS WFB 100°C, T 125° PS21212 TRANSFER-MOLD TYPE INSULATED TYPE Limits Unit Min. Typ. Max. 10 — 15 kg·cm 0.98 — 1.47 N·m — 54 — g Limits Unit Min. Typ. Max. 0 300 400 V 13.5 15.0 16.5 V 13.5 15.0 16.5 ...

Page 6

... Error output Fo (N-side only) signal is set by the external capacitor C O active signal the IGBT doesn’t turn ON SET RESET reference voltage CR circuit time constant DELAY ( * Note signal is set by the external capacitor C O SET RESET PS21212 TRANSFER-MOLD TYPE INSULATED TYPE . Aug. 1999 ...

Page 7

... PWM control scheme used in the application and on the wiring impedances of the application’s printed circuit board the circuits start to operate when the next input is applied. DBr signal output. O RESET SET a1 UV DBt 4.7k DIP-IPM 1nF 1nF V (Logic) NC PS21212 TRANSFER-MOLD TYPE INSULATED TYPE RESET Aug. 1999 ...

Page 8

... S V VFB V VFS COM WFB V WFS COM S U OUT OUT OUT CIN V NC GND CFO CFO CIN C4 time constant in the range 1.5 PS21212 TRANSFER-MOLD TYPE INSULATED TYPE category ceramic capacitor for noise filtering DIP-IPM Shunt R Resistor Sh N1 terminals (C ). (Example : Aug. 1999 ...

Related keywords