MIC5247-1.5YM5 Micrel Inc, MIC5247-1.5YM5 Datasheet
MIC5247-1.5YM5
Available stocks
Related parts for MIC5247-1.5YM5
MIC5247-1.5YM5 Summary of contents
Page 1
... Available in the 6-pin 2mm × 2mm ® MLF™ package and the IttyBitty MIC5247 also offers a range of fixed output voltages. All support documentation can be found on Micrel’s web site at www.micrel.com. Typical Application MIC5247-x ...
Page 2
... MIC5247 Ordering Information Part Number Standard Marking Pb-Free MIC5247-1.5BM5 LU15 MIC5247-1.5YM5 MIC5247-1.6BM5 LU16 MIC5247-1.6YM5 MIC5247-1.8BM5 LU18 MIC5247-1.8YM5 MIC5247-1.85BM5 LU1J MIC5247-1.85YM5 MIC5247-2.0BM5 LU20 MIC5247-2.0YM5 MIC5247-2.1BM5 LU21 MIC5247-2.1YM5 MIC5247-2.2BM5 LU22 MIC5247-2.2YM5 MIC5247-2.4BM5 LU24 MIC5247-2.4YM5 MIC5247-1.8BD5 NU18 MIC5247-1.8YD5 MIC5247-2.0BD5 NU20 MIC5247-2.0YD5 MIC5247-1.5BML U15 MIC5247-1.5YML MIC5247-1 ...
Page 3
... MIC5247 Absolute Maximum Ratings Supply Input Voltage (V ) ....................................0V to +7V IN Enable Input Voltage (V ) ................................... Junction Temperature (T ) ....................................... +150°C J Storage Temperature (T ) ........................ –65°C to +150°C S Lead Temperature (soldering, 5 sec.) ........................ 260°C (3) ESD Rating Electrical Characteristics 1.0V 100µ OUT IN EN OUT Symbol Parameter V Output Voltage Accuracy O Δ ...
Page 4
... MIC5247 Typical Characteristics Power Supply Rejection Ratio 1µ 0.01µF 80 BYP BYP BYP 100µ 3. 2.4V OUT 10µF Ceramic OUT 0 FREQUENCY (Hz) Power Supply Rejection Ratio 60 0. BYP I = 150mA 3. 2.4V OUT Ceramic OUT 0 10 10k 100k 1M 100 1k FREQUENCY (Hz) Ground Pin Current 100 ...
Page 5
... MIC5247 Typical Characteristics, cont. Output Voltage vs. Temperature 2.5 2 100µA LOAD 2.3 -40 -10 20 TEMPERATURE ( °C) February 2006 200 150 100 110 140 5 Turn-On Time vs. Bypass Capacitance C = 10µF OUT I = 100mA LOAD Rise Time Prop Delay 0 BYPASS CAPACITOR (µF) Micrel, Inc. M9999-022406 ...
Page 6
... MIC5247 Functional Characteristics Load Transient Response TIME (100µs/div.) M9999-022406 C = 10µF OUT BYP 2.4V OUT 100mA 100µA 6 Micrel, Inc. Line Transient Response 4.4V 3. 10µF OUT V = 2.4V OUT I = 100µA LOAD TIME (500µs/div.) February 2006 ...
Page 7
... MIC5247 Block Diagram IN Reference Voltage E N Thermal Sensor Under- voltage Lockout GND February 2006 Startup/ Quickstart/ Shutdown Noise Control Cancellation FAUL T Error Current Amplifier Amplifier AC TIVE OWN 7 Micrel, Inc OUT DOWN M9999-022406 ...
Page 8
... MIC5247 Applications Information Enable/Shutdown The MIC5247 comes with an active-high enable pin that can disable the regulator. Forcing the enable pin low disables the regulator and sends it into a “zero” off-mode-current state. In this state, current consumed by the regulator goes nearly to zero. Forcing the enable pin high enables the output volt- age. This part is CMOS and the enable pin cannot be left fl ...
Page 9
... MIC5247 Figure 1 includes a 0.01µF capacitor for low-noise opera- tion and shows EN (pin 3) connected to IN (pin 1) for an application where enable/shutdown is not required. C 1µF minimum. February 2006 MIC5247-x.xBM5 OUT Enable Shutdown E N Figure 2. Low-Noise Fixed Voltage Application Figure example of a low-noise configuration where C is not required ...
Page 10
... MIC5247 Package Information M9999-022406 SOT-23-5 (M) TSOT-23-5 (D5) 10 Micrel, Inc. February 2006 ...
Page 11
... MIC5247 MICREL, INC. 1849 FORTUNE DRIVE SAN JOSE, CA 95131 USA + 1 (408) 944-0800 TEL The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. ...