ICX081AK Sony, ICX081AK Datasheet
ICX081AK
Related parts for ICX081AK
ICX081AK Summary of contents
Page 1
... Diagonal 6mm (Type 1/3) CCD Image Sensor for PAL Color Video Cameras Description The ICX081AK is an interline CCD solid-state image sensor suitable for PAL color video cameras. This chip conforms to DV standard SD mode, and has the optimal number of pixels for MPEG2 Main level ...
Page 2
... Reset gate clock H Horizontal register transfer clock 1 H Horizontal register transfer clock 2 Ratings Unit Remarks –40 to +10 V –50 to +15 V –50 to +0.3 V –40 to +0.3 V – –0.3 to +18 V –10 to +18 V – –0.3 to +28 V –0 +15 V – –13 to +13 V –30 to +80 °C –10 to +60 °C ICX081AK 2 ...
Page 3
... V RGLL 0.5 V RGLm 17.3 18.5 19.3 V – 3 – Max. Unit Remarks 12.36 V Max. Unit Remarks mA Waveform Remarks diagram VH1 VH2 VL3 VL4 – High-level coupling 2 High-level coupling 2 Low-level coupling 2 Low-level coupling Cross-point voltage 4 4 Low-level coupling 4 Low-level coupling 5 ICX081AK L )/2 )/2 ...
Page 4
... Vertical transfer clock equivalent circuit Symbol V12 V23 C V13 C V24 SUB GND V23 C V13 Horizontal transfer clock equivalent circuit – 4 – Min. Typ. Max. Unit Remarks 1000 pF V3 560 pF V4 470 pF V34 390 pF V41 180 pF 100 270 kΩ ICX081AK Ω Ω Ω ...
Page 5
... VHH VHH V V VHL V VH2 V VL2 V VLL )/2 VH VH1 VH2 )/2 VL VL3 VL4 – VHn VLn twh VHH V VHL V VHL V VL3 VHL V VLH V VLL V VL4 – 5 – VHH VHH V VHL V VH3 V VLL VHH VHH VHL V VHL V VH4 V VLH V VL ICX081AK V VLH ...
Page 6
... V RGH V RG Point A is the minimum value of the coupling waveform during the period from RGLL . RGLm 100% 90% V SUB 10 twh – 6 – twl V and H waveforms and H is two twl is the average value of V RGL ICX081AK RGL and RGLH ...
Page 7
... Wave Length [nm] – 7 – Unit Remarks 0.5 0.5 µs 15 250 ns 8 8.5 14 8.5 14 0.01 0.01 µs 0.01 0. 0.5 0.5 µs Unit Remarks Max. ns 650 700 ICX081AK During readout During CXD1267AN used tf ≥ tr – 2ns During drain charge ...
Page 8
... Lcb 3 Lcw 3 Lag 0 774 (V) 6 Ignored region Effective pixel region LPF1 (3dB down 8MHz LPF2 S H (3dB down 1MHz) – 8 – Measurement method signal output [ C] Chroma signal output ICX081AK (Ta = 25°C) Remarks Ta = 60°C Zone 0 and I Zone 60° 60°C, ...
Page 9
... As shown in the left figure, fields are read out. The charge is Ye mixed by pairs such as A1 and A2 in the A field. (pairs such the B field result, the sequence of charges output as signals from Ye the horizontal shift register (Hreg) is, for line A1 Cy), A2 ( Cy), and (Mg + Ye). G Hreg – 9 – ICX081AK ...
Page 10
... Cbmin [mV]) values of the R – Y and B – Y channels of the chroma signal and substitute the values into the following formula. ∆ (Crmax – Crmin)/200 | x 100 [%] ∆ (Cbmax – Cbmin)/200 | x 100 [%] 2 , color temperature of 3200K halogen source subject. x 100 [%] (1/10V method conversion value) – 10 – ICX081AK ...
Page 11
... Adjust the Y signal output value generated by strobe light to 200mV. After setting the strobe light so that it strobes with the following timing, measure the residual signal (Ylag). Substitute the value into the following formula. Lag = (Ylag/200) x 100 [%] VD Strobe light timing Output Light Y signal output 200mV Ylag (lag) – 11 – ICX081AK ...
Page 12
... ICX081AK ...
Page 13
... ICX081AK ...
Page 14
... ICX081AK ...
Page 15
... ICX081AK ...
Page 16
... ICX081AK ...
Page 17
... If a load is applied to the entire surface by a hard component, bending stress may be generated and the package may fracture, etc., depending on the flatness of the bottom of the package. Therefore, for installation, use either an elastic load, such as a spring plate adhesive. 50N 50N Compressive strength – 17 – ICX081AK 1.2Nm Torsional strength ...
Page 18
... For continuous using under cruel condition exceeding the normal using condition, consult our company. b) Exposure to high temperature or humidity will affect the characteristics. Accordingly avoid storage or usage in such conditions. c) The brown stain may be seen on the bottom or side of the package. But this does not affect the CCD characteristics. – 18 – ICX081AK ...
Page 19
... ICX081AK ...