CS2001 ON Semiconductor, CS2001 Datasheet

no-image

CS2001

Manufacturer Part Number
CS2001
Description
1.2A Switching Regulator, and 5.0 V 100mA Linear Regulator with RESETbar
Manufacturer
ON Semiconductor
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
CS2001
Manufacturer:
LGIC
Quantity:
6 226
airbag systems. It contains a current–mode switching regulator with a
1.2 A on–chip switch and a 5.0 V, 100 mA linear regulator. The linear
output capacitor must be 3.3 F or greater with an ESR in the range of
100 m to 1.0 . If the ESR of the cap is less than 100 m , a series
resistor must be used. The switcher can be configured in either a boost
or flyback topology. The boost topology produces energy reserve
voltage VER which is externally adjustable (25 V maximum) through
the resistor divider connected to the V
conditions that produce V
shut down.
loading on the linear regulator is directed through V
or loss of battery condition switches the supply for the linear regulator
from V
internal “smartswitch.” This switchover feature minimizes the power
dissipation in both the linear and switcher output devices and saves the
cost of using a larger inductor.
output. If V
function whose time interval is externally adjustable with the
capacitor. This interval can be seen on the RESETB pin, which allows
for clean power–up and power–down of the microprocessor. Once
V
low) indicates to the microprocessor whether or not the VER pin is
connected.
produces output voltage V
is used in the system to drive high–side FETs.
The linear regulator will not shut down during this event.
Features
December, 2000 – Rev. 5
OUT
The CS2001 is a smart power supply ASIC utilized in automotive
Under normal operating conditions (V
The NERD (No Energy Reserve Detected) pin is a dual function
A switched–capacitor voltage tripler accepts input voltage VER and
This part is capable of withstanding a 50 V peak transient voltage.
Linear Regulator 5.0 V 2% @ 100 mA
Switching Regulator 1.2 A Peak Internal Switch
Voltage Tripler
Smart Functions
Protection
Internally Fused Leads in SO–20L Package
Semiconductor Components Industries, LLC, 2001
Smartswitch
RESET
Energy Reserve Status
Overtemperature
Current Limit
50 V Peak Transient Capability
is in regulation, the logic level of the NERD output (usually
BAT
to VER and shuts down the switcher using the ASIC’s
OUT
is not in regulation, it provides a Power On Reset
CHG
FB
either open or shorted, the switcher is
(typically VER + 8.0 V). This voltage
FB
BAT
pin. In the event of fault
> 8.0 V), the current
BAT
. A low battery
1
CS2001YDWF20
CS2001YDWFR20
20
Device
ORDERING INFORMATION
A
WL, L
YY, Y
WW, W = Work Week
SWSD
COMP
GND1
GND2
GND3
GND4
V
VER
MARKING DIAGRAM
V
PIN CONNECTIONS
V
BAT
20
http://onsemi.com
SW
1
1
FB
AWLYYWW
= Assembly Location
= Wafer Lot
= Year
1
CS2001
Package
SO–20L
SO–20L
Publication Order Number:
DWF SUFFIX
20
CASE 751D
1000 Tape & Reel
SO–20L
V
RESETB
NERD
GND8
GND7
GND6
GND5
V
I
C
BIAS
OUT
CHG
PUMP
37 Units/Rail
Shipping
CS2001/D

Related parts for CS2001

CS2001 Summary of contents

Page 1

... The CS2001 is a smart power supply ASIC utilized in automotive airbag systems. It contains a current–mode switching regulator with a 1.2 A on–chip switch and a 5.0 V, 100 mA linear regulator. The linear output capacitor must be 3 greater with an ESR in the range of 100 the ESR of the cap is less than 100 series resistor must be used ...

Page 2

... C. *The maximum package power dissipation must be observed. CS2001 Microprocessor 100 VER V RESETB BAT V NERD FB GND1 GND8 GND2 GND7 CS2001 GND3 GND6 GND4 GND5 SWSD COMP 1.0 F 0.1 F Figure 1. Application Diagram Rating Reflow: (SMD styles only) (Note 1.) http://onsemi ...

Page 3

... V – VER VER = CHG Initial Charge Time C Maximum Output Voltage Clamp V CHG Output Voltage Clamp V VER = CHG Short Circuit Path Current Limit VER to V CHG CS2001 (8 8.0 V VER 25 V, 1.0 mA BAT Test Conditions , VER = 25 V BAT = 0 V BAT @ I = –100 mA, V(BAT) V(OUT) SWSD = 4 ...

Page 4

... Output Low Voltage Pull–Up Current Power On Delay Clamping Voltage (Low) Clamping Voltage (High) General VER Load Current Thermal Shutdown PACKAGE PIN # SO–20L PIN SYMBOL CS2001 (8 8.0 V BAT Test Conditions = 0 V BAT V Increasing OUT V Decreasing OUT – 1 100 A OUT RESETB I = 1.0 mA 4.5 V ...

Page 5

... BIAS C Oscillator PUMP V REF 1.25 V Bandgap Reference V BAT V REF 7.25 V Over Temperature NERD V CC RESETB CS2001 Switched cap voltage tripler output. CHG Ground. Ground. Ground. Ground. No energy reserve detected output. Reset output. Linear regulator output. OUT V REF PUMP Short – Detect ...

Page 6

... I = 30mA. VER Figure 3. Typical Operation with I CS2001 CIRCUIT DESCRIPTION Figure oscilloscope waveform showing the voltage tripler output and the energy reserve input during power up. Figure 4. Startup with VER http://onsemi ...

Page 7

... PACKAGE DIMENSIONS DWF SUFFIX CASE 751D– 20X A e 18X A1 T PACKAGE THERMAL DATA Parameter R Typical JC R Typical JA http://onsemi.com CS2001 SO–20L ISSUE SO–20L Unit 9 C ...

Page 8

... Email: ONlit–asia@hibbertco.com JAPAN: ON Semiconductor, Japan Customer Focus Center 4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031 Phone: 81–3–5740–2745 Email: r14525@onsemi.com ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. http://onsemi.com 8 CS2001/D ...

Related keywords