X25080P Xicor, X25080P Datasheet
X25080P
Related parts for X25080P
X25080P Summary of contents
Page 1
... LOGIC HOLD WRITE CONTROL AND TIMING WP LOGIC Direct Write™ and Block Lock™ Protection is a trademark of Xicor, Inc. ©Xicor, Inc. 1994, 1995, 1996 Patents Pending 3090-1.7 6/11/96 T3/C1/D0 NS X25080 2 PROM With Block Lock DESCRIPTION The X25080 is a CMOS 8192-bit serial E internally organized ...
Page 2
X25080 PIN DESCRIPTIONS Serial Output (SO push/pull serial data output pin. During a read cycle, data is shifted out on this pin. Data is clocked out by the falling edge of the serial clock. Serial Input (SI) ...
Page 3
X25080 PRINCIPLES OF OPERATION 2 The X25080 PROM designed to interface directly with the synchronous serial peripheral interface (SPI) of many popular microcontroller families. The X25080 contains an 8-bit instruction register accessed ...
Page 4
X25080 Write-Protect Enable The Write-Protect-Enable (WPEN) is available for the X25080 as a nonvolatile enable bit for the WP pin. Protected Unprotected WPEN WP WEL Blocks Protected Protected Protected 1 LOW 0 Protected Protected ...
Page 5
X25080 Operational Notes The X25080 powers-up in the following state: • The device is in the low power standby state. • A HIGH to LOW transition required to enter an active state and receive an instruction. • ...
Page 6
X25080 Figure 3. Write Enable Latch Sequence CS SCK SI SO Figure 4. Byte Write Operation Sequence SCK INSTRUCTION SI HIGH IMPEDANCE HIGH IMPEDANCE 5 ...
Page 7
X25080 Figure 5. Page Write Operation Sequence SCK INSTRUCTION SCK DATA BYTE Figure 6. Write Status Register Operation ...
Page 8
X25080 ABSOLUTE MAXIMUM RATINGS* Temperature under Bias .................. – +135 C Storage Temperature ....................... – +150 C Voltage on any Pin with Respect to V D.C. Output Current ............................................. 5mA Lead Temperature (Soldering, 10 seconds) .............................. ...
Page 9
X25080 EQUIVALENT A.C. LOAD CIRCUIT 5V 1.44K 1.64K OUTPUT OUTPUT 1.95K 4.63K 100pF A.C. CHARACTERISTICS (Over recommended operating conditions, unless otherwise specified) Data Input Timing Symbol Parameter f Clock Frequency SCK t Cycle Time CYC CS Lead Time t LEAD ...
Page 10
X25080 Serial Output Timing CS SCK MSB OUT ADDR SI LSB IN Serial Input Timing CS t LEAD SCK MSB IN HIGH IMPEDANCE CYC MSB–1 OUT t t ...
Page 11
X25080 Hold Timing CS SCK SO SI HOLD 3090 ILL F12.1 SYMBOL TABLE WAVEFORM INPUTS Must be steady May change from LOW to HIGH May change from HIGH ...
Page 12
X25080 PACKAGING INFORMATION HALF SHOULDER WIDTH ON ALL END PINS OPTIONAL 0.015 (0.38) TYP. 0.010 (0.25) NOTE: 1. ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 2. PACKAGE DIMENSIONS EXCLUDE MOLDING FLASH 8-LEAD PLASTIC DUAL IN-LINE PACKAGE TYPE P 0.430 ...
Page 13
X25080 PACKAGING INFORMATION 8-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S PIN 1 INDEX 0.010 (0.25) 0.020 (0.50) 0 – 8 0.016 (0.410) 0.037 (0.937) NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 0.150 (3.80) 0.158 (4.00) PIN ...
Page 14
X25080 PACKAGING INFORMATION 14-LEAD PLASTIC, TSSOP PACKAGE TYPE V 0 – 8 See Detail “A” NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) .025 (.65) BSC .169 (4.3) .252 (6.4) BSC .177 (4.5) .193 (4.9) .200 (5.1) .047 (1.20) ...
Page 15
... LIMITED WARRANTY Devices sold by Xicor, Inc. are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. Xicor, Inc. makes no warranty, express, statutory, implied description regarding the information set forth herein or regarding the freedom of the described devices from patent infringement. ...