MAX9728AETC+T Maxim Integrated Products, MAX9728AETC+T Datasheet - Page 9
![IC AMP AUDIO .06W STER AB 12TQFN](/photos/6/61/66135/12-tqfn_21-0136i_sml.jpg)
MAX9728AETC+T
Manufacturer Part Number
MAX9728AETC+T
Description
IC AMP AUDIO .06W STER AB 12TQFN
Manufacturer
Maxim Integrated Products
Series
DirectDrive™r
Type
Class ABr
Datasheet
1.MAX9728AETC.pdf
(19 pages)
Specifications of MAX9728AETC+T
Output Type
Headphones, 2-Channel (Stereo)
Max Output Power X Channels @ Load
60mW x 2 @ 32 Ohm
Voltage - Supply
4.5 V ~ 5.5 V
Features
Depop, Short-Circuit and Thermal Protection, Shutdown
Mounting Type
Surface Mount
Package / Case
12-TQFN Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Use ceramic capacitors with a low ESR for optimum
performance. For optimal performance over the extend-
ed temperature range, select capacitors with an X7R
dielectric. Table 1 lists suggested manufacturers.
The value of the flying capacitor (see the Functional
Diagram/Typical Operating Circuits ) affects the charge
pump’s load regulation and output resistance. A C1
value that is too small degrades the device’s ability to
provide sufficient current drive, which leads to a loss of
output voltage. Increasing the value of C1 improves load
regulation and reduces the charge-pump output resis-
tance to an extent. See the Output Power vs. Load
Resistance and Charge-Pump Capacitor Size graph in
the Typical Operating Characteristics . Above 1µF, the
on-resistance of the switches and the ESR of C1 and C2
dominate.
The hold capacitor value (see the Functional
Diagram/Typical Operating Circuits ) and ESR directly
affect the ripple at PV
reduces output ripple. Likewise, decreasing the ESR of
C2 reduces both ripple and output resistance. Lower
capacitance values can be used in systems with low
maximum output power levels. See the Output Power
vs. Load Resistance and Charge-Pump Capacitor Size
graph in the Typical Operating Characteristics .
The power-supply bypass capacitor (see the Functional
Diagram/Typical Operating Circuits ) lowers the output
impedance of the power supply, and reduces the
impact of the MAX9728A/MAX9728Bs’ charge-pump
Table 1. Suggested Capacitor Manufacturers
Taiyo Yuden
TDK
Murata
SUPPLIER
Power-Supply Bypass Capacitor (C3)
_______________________________________________________________________________________
Charge-Pump Capacitor Selection
SS
60mW, DirectDrive, Stereo Headphone
. Increasing the value of C2
800-348-2496
847-803-6100
770-436-1300
Flying Capacitor (C1)
PHONE
Hold Capacitor (C2)
Amplifier with Shutdown
847-925-0899
847-390-4405
770-436-3030
switching transients. Bypass V
value as C1, and place it physically close to the V
and PGND pins.
The gain of the MAX9728B amplifier is internally set to
-1.5V/V. All gain-setting resistors are integrated into the
device, reducing external component count. The inter-
nally set gain, in combination with DirectDrive, results in
a headphone amplifier that requires only five small
capacitors to complete the amplifier circuit: two for the
charge pump, two for audio input coupling, and one for
power-supply bypassing (see the Functional
Diagram/Typical Operating Circuits ).
The gain of the MAX9728A amplifier is set externally as
shown in Figure 2, the gain is:
Choose feedback resistor values in the tens of kΩ
range. Lower values may cause excessive power dissi-
pation and require impractically small values of R
large gain settings. The high-impedance state of the
outputs can also be degraded during shutdown mode if
an inadequate feedback resistor is used since the
equivalent output impedance during shutdown is
14kΩ||R
source resistance of the input device may also need to
be taken into consideration. Since the effective value of
R
input device and the value of the input resistor connect-
ed to the inverting terminal of the headphone amplifier
(20kΩ for the MAX9728B), the overall closed-loop gain
of the headphone amplifier can be reduced if the input
resistor is not significantly larger than the source resis-
tance of the input device.
FAX
IN
is equal to the sum of the source resistance of the
F
(R
F
is equal to 30kΩ for the MAX9728B). The
www.t-yuden.com
www.component.tdk.com
www.murata.com
A
V
= -R
F
/R
IN
WEBSITE
(V/V)
DD
with C3, the same
Amplifier Gain
IN
DD
for
9