ATF22V10B-10JI ATMEL Corporation, ATF22V10B-10JI Datasheet
ATF22V10B-10JI
Available stocks
Related parts for ATF22V10B-10JI
ATF22V10B-10JI Summary of contents
Page 1
... GND DIP/SOIC LCC/PLCC CLK/ VCC I/O GND High- performance EE PLD ATF22V10B 25 I I/O 20 I/O 19 I/O Rev. 0250L–PLD–06/03 1 ...
Page 2
... Description The ATF22V10B is a high-performance CMOS (electri- cally-erasable) programmable logic device (PLD) which utilizes Atmel’s proven electrically-erasable Flash memory technology. Speeds down to 7.5 ns and power dissipation as low are offered. All speed ranges are specified over the full 5V 10% range for military and industrial Absolute Maximum Ratings* Temperature Under Bias................................ -55° ...
Page 3
DC Characteristics Symbol Parameter Input or I Low Leakage Current Input or I High Leakage Current Power Supply Current Standby Power Supply Current Standby Clocked Power I CC2 Supply Current Output Short ...
Page 4
... Setup Time, Synchronous Preset SP Synchronous Preset to t SPR Clock Recovery Time Notes: 1. See ordering information for valid part numbers. 2. 5.5 ns for DIP package devices. 3. 111 MHz for DIP package devices. 4. The shaded devices are obsolete. ATF22V10B 4 -7 -10 Min Max Min Max 3 7.5 3 ...
Page 5
... OUT Note: 1. Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. Power-up Reset The registers in the ATF22V10Bs are designed to reset during power-up point delayed slightly from V ing V , all registers will be reset to the low state. The RST output state will depend on the polarity of the output buffer ...
Page 6
... Input Diagram ATF22V10B 6 Input and I/O Pull-ups All ATF22V10B family members have internal input and I/O pull-up resistors. Therefore, whenever inputs or I/Os are not being driven externally, they will float to V ensures that all logic array inputs are at known states. These are relatively weak active pull-ups that can easily be overdriven by TTL-compatible drivers (see input and I/O diagrams below) ...
Page 7
... Functional Logic Diagram ATF22V10B 7 ...
Page 8
... ATF22V10B 8 ...
Page 9
9 ...
Page 10
... ATF22V10B 10 ...
Page 11
... Notes: 1. Recommend ATF22V10C versions. 2. The shaded devices are obsolete. Ordering Code (1) ATF22V10B-7JC (1) ATF22V10B-7PC (1) ATF22V10B-7SC (1) ATF22V10B-7XC (1) ATF22V10B-10JC (1) ATF22V10B-10PC (1) ATF22V10B-10SC (1) ATF22V10B-10XC (1) ATF22V10B-10JI (1) ATF22V10B-10PI (1) ATF22V10B-10SI (1) ATF22V10B-10XI ATF22V10B-10GM/883 ATF22V10B-10NM/883 5962-89841 06LA 5962-89841 063X (1) ATF22V10B-15JC (1) ATF22V10B-15PC (1) ATF22V10B-15SC (1) ATF22V10B-15XC (1) ATF22V10B-15JI (1) ATF22V10B-15PI (1) ATF22V10B-15SI (1) ATF22V10B-15XI ATF22V10B-15GM/883 ...
Page 12
... ATF22V10BQ(L) Ordering Information t (ns) t (ns) t (ns Notes: 1. Recommend ATF22V10CQ and ATF22V10CQZ 2. The shaded devices are obsolete. ATF22V10B 12 Ordering Code (1) ATF22V10BQ-15JC (1) ATF22V10BQ-15PC (1) ATF22V10BQ-15SC (1) ATF22V10BQ-15XC (1) ATF22V10BQL-20JC (1) ATF22V10BQL-20PC (1) ATF22V10BQL-20SC (1) ATF22V10BQL-20XC (1) ATF22V10BQL-20JI (1) ATF22V10BQL-20PI (1) ATF22V10BQL-20SI (1) ATF22V10BQL-20XI ATF22V10BQL-20GM/883 ATF22V10BQL-20NM/883 5962-89841 14 LA ...
Page 13
Package Information 24D3 24D3, 24-lead, 0.300"Wide. Non-windowed, Ceramic Dual Inline Parkage (Cerdip) Dimensions in Millimeters and (Inches)* MIL-STD-1835 D-9 CONFIG A (Glass Sealed) 5.08(0.200) MAX SEATING PLANE 5.08(0.200) 3.18(0.125) 2.45(0.100)BSC 0.46(0.018) 0.20(0.008) *Controlling dimension: Inches REV. A 04/11/2001 32.51(1.280) 31.50(1.240) ...
Page 14
... Non-windowed, Ceramic lid, Leadless Chip Carrier (LCC) Dimensions in Millimeters and (Inches)* MIL-STD-1835 C-4 11.68(0.460) 11.23(0.442) 7.62(0.300) BSC 1.27(0.050) TYP ATF22V10B 14 11.68(0.460) 11.23(0.442) PIN 1 1.40(0.055) 1.14(0.045) 2.41(0.095) 1.91(0.075) 0.635(0.025) 0.381(0.015) 0.305(0.012) 0.178(0.007) 0.737(0.029) 0.533(0.021) 1.02(0.040) X 45˚ ...
Page 15
... Fax: (81) 3-3523-7581 Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information contained herein ...