SP211HCA Exar Corporation, SP211HCA Datasheet
SP211HCA
Available stocks
Related parts for SP211HCA
SP211HCA Summary of contents
Page 1
High Speed +5V High Performance Single +5V Supply Operation 0.1 F External Charge Pump Capacitors 500Kbps Data Rate Under Load Standard SOIC and SSOP Packages Lower Supply Current Than Competition (typical 3mA Shutdown Mode WakeUp Feature in ...
Page 2
ABSOLUTE MAXIMUM RATINGS These are stress ratings only and functional operation of the device at these or any other above those indicated in the operation sections of the specifications below is not implied. Exposure to absolute maximum rating conditions for ...
Page 3
SPECIFICATIONS V at nominal ratings; 0.1 F charge pump capacitors PARAMETER MIN. POWER REQUIREMENTS V CC SP207EH 4.75 All other parts 4. Shutdown Current ENVIRONMENTAL AND MECHANICAL Operating Temperature Commercial, –C Extended, –E –40 Storage Temperature ...
Page 4
PINOUT T OUT OUT OUT OUT GND ...
Page 5
FEATURES As in the original RS-232 multi-channel products, the SP207EH Series high speed multi-channel RS-232 line transceivers provide a variety of configurations to fit most designs, especially high speed applications where +12V is not available. The SP207EH Series is a ...
Page 6
– Figure 2. Charge Pump — Phase 2 Phase 4 — V transfer — The fourth phase of the clock DD connects the negative terminal of C and transfers the generated l0V across C the V ...
Page 7
– –5V Figure 4. Charge Pump — Phase + – Figure 5. Charge Pump — Phase 4 Receivers The high performance receivers of the SP207EH Series can accept ...
Page 8
ENABLE The SP211EH and SP213EH all feature an enable input, which allows the receiver outputs to be either tri–stated or enabled. This can be especially useful when the receiver is tied di- rectly to a microprocessor data bus. For the ...
Page 9
WAKEUP FUNCTION The SP213EH has a wake–up feature that keeps two receivers (R and enabled state 4 5 when the device is in the shutdown mode. With only the receivers active during shutdown, the devices draw ...
Page 10
SW1 SW1 SW1 DC Power Source Figure 8. ESD Test Circuit for IEC1000-4-2 With the Air Discharge Method, an ESD voltage is applied to the equipment under test (EUT) through air. This simulates an ...
Page 11
For the Human Body Model, the current limiting resistor (R ) and the source capacitor (C S 1.5k an 100pF, respectively. For IEC-1000-4-2, the current limiting resistor (R ) and the source S capacitor (C ) are 330 an 150pF, ...
Page 12
TYPICAL APPLICATION CIRCUITS...SP207EH TO SP213EH +5V INPUT 9 10 0.1µ 6.3V 0.1µ 6. – – 0.1µF SP207EH 16V 14 C – 2 400KOHM ...
Page 13
DIMENSIONS (Inches) Minimum/Maximum SP207EHDS/08 PACKAGE: PLASTIC SHRINK H A 24–PIN (mm) A 0.068/0.078 0.068/0.078 (1.73/1.99) (1.73/1.99) A1 0.002/0.008 0.002/0.008 (0.05/0.21) (0.05/0.21) B 0.010/0.015 0.010/0.015 (0.25/0.38) (0.25/0.38) D 0.317/0.328 0.397/0.407 (8.07/8.33) (10.07/10.33) E 0.205/0.212 0.205/0.212 (5.20/5.38) ...
Page 14
DIMENSIONS (Inches) Minimum/Maximum SP207EHDS/08 PACKAGE: PLASTIC SMALL OUTLINE (SOIC) (WIDE) H 24–PIN 28–PIN (mm) A 0.093/0.104 0.093/0.104 (2.352/2.649) (2.352/2.649) A1 0.004/0.012 0.004/0.012 (0.102/0.300) (0.102/0.300) B 0.013/0.020 0.013/0.020 (0.330/0.508) (0.330/0.508) D 0.599/0.614 0.697/0.713 (15.20/15.59) (17.70/18.09) ...
Page 15
D1 = 0.005" min. (0.127 min 0.100 BSC (2.540 BSC) ALTERNATE END PINS (BOTH ENDS) SP207EHDS/08 PACKAGE: PLASTIC DUAL–IN–LINE (NARROW 0.015" min. (0.381min 0.210" max. (5.334 max ...
Page 16
RS232 Transceivers: Model .................... Drivers .......................... Receivers ..................................... Temperature Range ................................. Package Type SP207EHCA .............. 5 ....................................... 3 ................................................... +70 C ............................................... 24–pin SSOP SP207EHCP .............. 5 ....................................... 3 ................................................... +70 C ....................................... 24–pin ...