PDIUSBD11N Philips Semiconductors, PDIUSBD11N Datasheet
PDIUSBD11N
Available stocks
Related parts for PDIUSBD11N
PDIUSBD11N Summary of contents
Page 1
PDIUSBD11 USB device with serial interface Product specification Product specification Supersedes data of 1999 Nov 19 hilips Semiconductors INTEGRATED CIRCUITS 1999 Jul 22 ...
Page 2
... Philips Semiconductors USB device with serial interface FEATURES Complies with the Universal Serial Bus specification Rev. 1.1 Complies with the ACPI, OnNOW, and USB power management requirements Compliant with USB Human Interface Devices and Monitor Control Class Compliant with System Management Bus Specification Rev. 1.0 ...
Page 3
... Philips Semiconductors USB device with serial interface Analog Transceiver The transceiver interfaces directly to the USB cables through some termination resistors. They are capable of transmitting and receiving serial data at “full speed” (12 Mbit/s) only. PLL A 12 MHz to 48 MHz clock multiplier PLL (Phase-Locked Loop) is integrated on-chip ...
Page 4
... Philips Semiconductors USB device with serial interface PIN DESCRIPTION PIN NO PIN SYMBOL TYPE 1 TEST Input 2 RESET_N Input 3 XTAL1 Input 4 XTAL2 Output 5 CLKOUT Output 6 V Power CC 7 SUSPEND Output 8 INT_N Output 9 SDA I/O 10 SCL I/O 11 GND Power AI/O 14 AGND Power 15 AV Power CC 16 ...
Page 5
... Philips Semiconductors USB device with serial interface Interface 2 The I C bus is used to interface to an external microcontroller needed to control the operation of the USB device. For cost consideration, the target system microcontroller can be shared and utilized for both the functional part as well as the USB protocol interfacing ...
Page 6
... Philips Semiconductors USB device with serial interface COMMAND SUMMARY Some commands have the same command code (e.g., Read Buffer and Write Buffer). In these cases, the direction of the Data Phase (read or write) indicates which command is executed. COMMAND NAME Initialization Commands Set Address/Enable Function ...
Page 7
... Philips Semiconductors USB device with serial interface COMMAND DESCRIPTIONS Command Procedure There are three basic types of commands: Initialization, Data Flow, and General commands. Respectively, these are used to initialize the function; for data flow between the function and the host; and some general commands. ...
Page 8
... Philips Semiconductors USB device with serial interface Clock Division Factor Byte POWER ON VALUE CLOCK DIVISION FACTOR RESERVED Clock Division Factor The value indicates clock division factor for CLKOUT. The output frequency is 48 MHz/(N+1) where N is the Clock Division Factor ...
Page 9
... Philips Semiconductors USB device with serial interface Read Last Transaction Status Command : 40–4Dh Data : Read 1 byte The Read Last Transaction Status command is followed by one data read that returns the status of the last transaction of the endpoint. This command also resets the corresponding interrupt flag in the interrupt register, and clears the status, indicating that it was read ...
Page 10
... Philips Semiconductors USB device with serial interface Clear Buffer Command : F2h Data : None When a packet is received completely, an internal endpoint buffer full flag is set. All subsequent packets will be refused by returning a NAK. When the microcontroller has read the data, it should free the buffer by the Clear Buffer command. When the buffer is cleared, new packets will be accepted ...
Page 11
... Philips Semiconductors USB device with serial interface RECOMMENDED OPERATING CONDITIONS SYMBOL PARAMETER V DC supply voltage input voltage range input voltage range for I/O I input voltage range for analog I/O AI output voltage range O T Operating ambient temperature range in free air ...
Page 12
... Philips Semiconductors USB device with serial interface DC CHARACTERISTICS (AI/O pins) SYMBOL PARAMETER Leakage Current I Hi-Z state data line leakage LO Input Levels V Differential input sensitivity DI V Differential common mode range CM V Single-ended receiver threshold SE Output Levels V Static output LOW OL V Static output HIGH OH Capacitance ...
Page 13
... Philips Semiconductors USB device with serial interface AC CHARACTERISTICS (AI/O pins, FULL speed) SYMBOL PARAMETER Driver characteristics Transition Time: t Rise time r t Fall time f t Rise/fall time matching RFM V Output signal crossover voltage CRS Driver Timings t Source EOP width EOPT t Differential data to EOP transition skew ...
Page 14
... Philips Semiconductors USB device with serial interface 2 AC CHARACTERISTICS (I C pins) All timing values are valid within the operating supply voltage and ambient temperature range and reference to V swing of V and SYMBOL PARAMETER F S clock frequency SCL CL t Bus free time ...
Page 15
... Philips Semiconductors USB device with serial interface SO16: plastic small outline package; 16 leads; body width 7.5 mm 1999 Jul 22 15 Product specification PDIUSBD11 SOT162-1 ...
Page 16
... Philips Semiconductors USB device with serial interface DIP16: plastic dual in-line package; 16 leads (300 mil) 1999 Jul 22 16 Product specification PDIUSBD11 SOT38-4 ...
Page 17
... Philips Semiconductors USB device with serial interface SOLDERING Introduction This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our “Data Handbook IC26; Integrated Circuit Packages” (document order number 9398 652 90011). There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mount components are mixed on one printed circuit board ...
Page 18
... Philips Semiconductors USB device with serial interface SUITABILITY OF IC PACKAGES FOR WAVE, REFLOW AND DIPPING SOLDERING METHODS Mo nting Mounting Package Package Through-hole mount DBS, DIP, HDIP, SDIP, SIL BGA, SQFP, HLQFP, HSQFP, HSOP, SMS Surface mount PLCC, SO, SOJ LQFP, QFP, TQFP ...
Page 19
... Philips Semiconductors USB device with serial interface 1999 Jul 22 NOTES 19 Product specification PDIUSBD11 ...
Page 20
... Philips Semiconductors for any damages resulting from such application. Right to make changes — Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no ...