ICX039BLA Sony, ICX039BLA Datasheet
ICX039BLA
Available stocks
Related parts for ICX039BLA
ICX039BLA Summary of contents
Page 1
... ICX039BLA. Features • Low smear (–20dB compared with the ICX039BLA) • High sensitivity (+3.0dB compared with the ICX039BLA) • High D range (+2.5dB compared with the ICX039BLA) • High S/N • High resolution and low dark current • Excellent antiblooming characteristics • Continuous variable-speed shutter • ...
Page 2
Block Diagram and Pin Configuration (Top View Pin Description Pin No. Symbol 1 V Vertical register transfer clock Vertical register transfer clock Vertical register transfer clock 2 4 Substrate clock SUB 5 ...
Page 3
Absolute Maximum Ratings Item Substrate clock – GND SUB Supply voltage Clock input voltage Voltage difference between vertical clock input pins Voltage ...
Page 4
Bias Conditions 1 [when used in substrate bias internal generation mode] Item Output circuit supply voltage Reset drain voltage Output circuit gate voltage Output circuit source Protective transistor bias Substrate bias circuit supply voltage Substrate clock 1 V setting is ...
Page 5
Clock Voltage Conditions Item Symbol Readout clock voltage VH1 VH3 VL1 VL3 VH1 Vertical transfer clock voltage V VH3 V VH4 V ...
Page 6
Clock Equivalent Circuit Constant Item Capacitance between vertical transfer clock and GND Capacitance between vertical transfer clocks Capacitance between horizontal transfer clock and GND Capacitance between horizontal transfer clocks Capacitance between reset gate clock and GND Capacitance between substrate clock ...
Page 7
Drive Clock Waveform Conditions (1) Readout clock waveform 100% 90% 10% 0% (2) Vertical transfer clock waveform VH1 VHH VHL V VL1 V VLH V VLL VHH ...
Page 8
Horizontal transfer clock waveform 90% 10 (4) Reset gate clock waveform RG waveform V RGLH V RGLL H waveform 1 +2. the maximum value and V RGLH Point A in the above diagram until the ...
Page 9
Substrate clock waveform 100% V SUB Clock Switching Characteristics Item Symbol Readout clock V T Vertical transfer clock During H imaging During parallel serial H conversion ...
Page 10
Image Sensor Characteristics Item Symbol Sensitivity S Saturation signal Vsat Smear Sm Video signal shading SH Dark signal Vdt ∆Vdt Dark signal shading Flicker F Lag Lag Zone Definition of Video Signal Shading Min. Typ. Max. Unit 500 600 mV ...
Page 11
Image Sensor Characteristics Measurement Method Measurement conditions 1) In the following measurements, the device drive conditions are at the typical values of the bias and clock voltage conditions. (When used with substrate bias external adjustment, set the substrate voltage to ...
Page 12
Dark signal Measure the average value of the signal output (Vdt [mV]) with the device ambient temperature 60°C and the device in the light-obstructed state, using the horizontal idle transfer level as a reference. 6. Dark signal shading After ...
Page 13
ICX039DLA ...
Page 14
ICX039DLA ...
Page 15
Spectral Sensitivity Characteristics (Includes lens characteristics, excludes light source characteristics) 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0.0 400 500 Sensor Readout Clock Timing Chart V1 V2 Odd Field Even Field V3 V4 ...
Page 16
ICX039DLA ...
Page 17
ICX039DLA ...
Page 18
Notes on Handling 1) Static charge prevention CCD image sensors are easily damaged by static discharge. Before handling be sure to take the following protective measures. a) Either handle bare handed or use non-chargeable gloves, clothes or material. Also use ...
Page 19
The adhesive may cause the marking on the rear surface to disappear, especially in case the regulated voltage value is indicated on the rear surface. Therefore, the adhesive should not be applied to this area, and indicated values should ...
Page 20
ICX039DLA ...