MAX9778ETI+ Maxim Integrated Products, MAX9778ETI+ Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX9778ETI+
Manufacturer Part Number
MAX9778ETI+
Description
IC AMP AUDIO PWR 2.6W AB 28TQFN
Manufacturer
Maxim Integrated Products
Type
Class ABr
Datasheet
1.MAX9777ETIT.pdf
(27 pages)
Specifications of MAX9778ETI+
Output Type
2-Channel (Stereo) with Stereo Headphones
Max Output Power X Channels @ Load
2.6W x 2 @ 4 Ohm; 200mW x 2 @ 16 Ohm
Voltage - Supply
4.5 V ~ 5.5 V
Features
Depop, Input Multiplexer, Mute, Shutdown, Thermal Protection,
Mounting Type
Surface Mount
Package / Case
28-TQFN Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Stereo 3W Audio Power Amplifiers with
Headphone Drive and Input Mux
The MAX9777 features an I
wire serial interface consisting of a serial data line
(SDA) and a serial clock line (SCL). SDA and SCL facili-
tate bidirectional communication between the
MAX9777 and the master at clock rates up to 400kHz.
Figure 3 shows the 2-wire interface timing diagram. The
MAX9777 is a transmit/receive slave-only device, rely-
ing upon a master to generate a clock signal. The mas-
ter (typically a microcontroller) initiates data transfer on
the bus and generates SCL to permit that transfer.
A master device communicates to the MAX9777 by
transmitting the proper address followed by a com-
mand and/or data words. Each transmit sequence is
framed by a START (S) or REPEATED START (S
dition and a STOP (P) condition. Each word transmitted
over the bus is 8 bits long and is always followed by an
acknowledge clock pulse.
SDA and SCL are open-drain outputs requiring a pullup
resistor (500Ω or greater) to generate a logic-high volt-
age. Series resistors in line with SDA and SCL are option-
al. These series resistors protect the input stages of the
SMBus is a trademark of Intel Corp.
Figure 3. 2-Wire Serial-Interface Timing Diagram
Figure 4. START/STOP Conditions
14
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
SDA
SCL
t
HD, STA
CONDITION
START
t
LOW
2
t
C/SMBus™-compatible 2-
R
t
t
SU, DAT
HIGH
SDA
SCL
Digital Interface
t
F
S
t
HD, DAT
r
) con-
t
HD, STA
S
r
devices from high-voltage spikes on the bus lines, and
minimize crosstalk and undershoot of the bus signals.
One data bit is transferred during each SCL clock
cycle. The data on SDA must remain stable during the
high period of the SCL clock pulse. Changes in SDA
while SCL is high are control signals (see the START
and STOP Conditions section). SDA and SCL idle high
when the I
When the serial interface is inactive, SDA and SCL idle
high. A master device initiates communication by issu-
ing a START condition. A START condition is a high-to-
low transition on SDA with SCL high. A STOP condition
is a low-to-high transition on SDA while SCL is high
(Figure 4). A START condition from the master signals
the beginning of a transmission to the MAX9777. The
master terminates transmission by issuing the STOP
condition; this frees the bus. If a REPEATED START
condition is generated instead of a STOP condition, the
bus remains active.
CONDITION
REPEATED
START
t
HD, STA
2
C bus is not busy.
P
t
SP
START and STOP Conditions
t
SU, STO
CONDITION
STOP
t
BUF
Bit Transfer
CONDITION
START