MAX9755ETI+T Maxim Integrated Products, MAX9755ETI+T Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX9755ETI+T
Manufacturer Part Number
MAX9755ETI+T
Description
IC AMP AUDIO PWR 2.6W AB 28TQFN
Manufacturer
Maxim Integrated Products
Series
DirectDrive™r
Type
Class ABr
Datasheet
1.MAX9750AEUI.pdf
(30 pages)
Specifications of MAX9755ETI+T
Output Type
2-Channel (Stereo) with Stereo Headphones
Max Output Power X Channels @ Load
2.6W x 2 @ 3 Ohm; 110mW x 2 @ 16 Ohm
Voltage - Supply
4.5 V ~ 5.5 V
Features
Depop, Short-Circuit and Thermal Protection, Shutdown
Mounting Type
Surface Mount
Package / Case
28-TQFN Exposed Pad
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
significant amount of DC current flows to the headphone,
resulting in unnecessary power dissipation and possible
damage to both headphone and headphone amplifier.
Maxim’s DirectDrive architecture uses a charge pump to
an internal negative supply voltage. This allows the
MAX9750/MAX9751/MAX9755 headphone amplifier out-
put to be biased about GND, almost doubling the dynam-
ic range while operating from a single supply. With no DC
component, there is no need for the large DC-blocking
capacitors. Instead of two large capacitors (220µF typ),
the MAX9750/MAX9751/MAX9755 charge pump requires
only two small ceramic capacitors (1µF typ), conserving
board space, reducing cost, and improving the frequen-
cy response of the headphone amplifier. See the Output
Power vs. Charge-Pump Capacitance and Load
Resistance
Characteristics for details of the possible capacitor val-
ues.
Previous attempts to eliminate the output coupling
capacitors involved biasing the headphone return
(sleeve) to the DC bias voltage of the headphone
amplifiers. This method raised some issues:
1) The sleeve is typically grounded to the chassis. Using
2) During an ESD strike, the amplifier’s ESD structures
3) When using the headphone jack as a lineout to other
In addition to the cost and size disadvantages, the DC-
blocking capacitors limit the low-frequency response of
the amplifier and distort the audio signal:
1) The impedance of the headphone load to the DC-
this biasing approach, the sleeve must be isolated
from system ground, complicating product design.
are the only path to system ground. The amplifier
must be able to withstand the full ESD strike.
equipment, the bias voltage on the sleeve may con-
flict with the ground potential from other equipment,
resulting in large ground-loop current and possible
damage to the amplifiers.
blocking capacitor forms a highpass filter with the
-3dB point determined by:
where R
C
The highpass filter is required by conventional sin-
gle-ended, single-supply headphone amplifiers to
block the midrail DC component of the audio signal
from the headphones. Depending on the -3dB point,
OUT
is the value of the DC-blocking capacitor.
L
is the impedance of the headphone and
graph
f
2.6W Stereo Audio Power Amplifiers and
−
______________________________________________________________________________________
3
dB
=
in
2π
Low-Frequency Response
R C
the
L OUT
1
DirectDrive Headphone Amplifiers
Typical
Operating
2) The voltage coefficient of the capacitor, the change
The combination of low-frequency attenuation and fre-
quency-dependent distortion compromises audio
reproduction. DirectDrive improves low-frequency
reproduction in portable audio equipment that empha-
sizes low-frequency effects such as multimedia lap-
tops, and MP3, CD, and DVD players.
The MAX9750/MAX9751/MAX9755 feature a low-noise
charge pump. The 550kHz switching frequency is well
beyond the audio range, and does not interfere with the
audio signals. The switch drivers feature a controlled
switching speed that minimizes noise generated by turn-
on and turn-off transients. Limiting the switching speed of
the charge pump minimizes the di/dt noise caused by the
Figure 3. Low-Frequency Attenuation of Common DC-Blocking
Capacitor Values
the filter can attenuate low-frequency signals within
the audio band. Larger values of C
attenuation but are physically larger, more expen-
sive capacitors. Figure 3 shows the relationship
between the size of C
quency attenuation. Note that the -3dB point for a
16Ω headphone with a 100µF blocking capacitor is
100Hz, well within the audio band.
in capacitance due to a change in the voltage
across the capacitor, distorts the audio signal. At
frequencies around the -3dB point, the reactance of
the capacitor dominates, and the voltage coefficient
appears as frequency-dependent distortion. Figure
4 shows the THD+N introduced by two different
capacitor dielectrics. Note that around the -3dB
point, THD+N increases dramatically.
-12
-15
-18
-21
-24
-27
-30
-3
-6
-9
0
10
LOW-FREQUENCY ROLLOFF
100
FREQUENCY (Hz)
33μF
(R
OUT
100μF
L
220μF
= 16Ω)
1k
330μF
DirectDrive
and the resulting low-fre-
10k
OUT
Charge Pump
100k
reduce the
13