PAH75S48-5 TDK Corporation, PAH75S48-5 Datasheet - Page 68
![no-image](/images/manufacturer_photos/0/6/653/tdk_corporation_sml.jpg)
PAH75S48-5
Manufacturer Part Number
PAH75S48-5
Description
Manufacturer
TDK Corporation
Datasheet
1.PAH75S48-5.pdf
(82 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PAH75S48-5
Manufacturer:
LAMBDA
Quantity:
32
Company:
Part Number:
PAH75S48-5
Manufacturer:
LAMBDA
Quantity:
1 000
Part Number:
PAH75S48-5
Quantity:
60
Company:
Part Number:
PAH75S48-5/P
Manufacturer:
LAMBDA
Quantity:
33
Company:
Part Number:
PAH75S48-5/P
Manufacturer:
VICOR
Quantity:
339
Company:
Part Number:
PAH75S48-5/V
Manufacturer:
LAMBDA
Quantity:
1 000
PAH
B-210
PAH
PAH75D48 SERIES module is not internally fused. To
ensure safe operation and to receive each safety standard
approval, please connect an external fuse F1 as shown in
the diagram above.
Input capacitor C1 is recommended to stabilize the mod-
ule when the module is powered from a high impedance
source. Capacitor C2 is used to absorb noise coming from
the module itself. This capacitor will also help the EMI per-
formance of the module.
The function of capacitor C3 is to reduce the output ripple
of the power module and high frequency noise that is pro-
duced by the module.
If in any application that an input reversal connection is
possible, a protective diode which is connected across
+Vin and -Vin is recommended.
3 Input Voltage Range
The operating input voltage range of PAH75D48 SERIES
is 36 - 76VDC. The maximum allowable input ripple volt-
age (Vrpl) is 4V. Any ripple that exceeds this value might
cause the module to become unstable.
4 Output Voltage Adjust Range
The output voltage of power module can be adjusted by
connecting an external resistor (R
pin and either the +Vo or –Vo pins. There are two options
available for the trim function for models 5033 & 3325,
which are standard & /Z option.
With an external resistor (R
pin, output voltage will decrease as shown in diagram be-
low.
If the external resistor (R
TRIM pin and –Vo pin, the output voltage will increase.
Diagram shown below is the output voltage trim up con-
nection.
75D48
+Vo2
-Vo2
TRM2
+Vo1
-Vo1
TRM1
Time
adj
adj
) is connected between the
) between TRIM pin and +Vo
Radj2
Radj1
Below
Vrpl
4V
adj
) between the TRIM
Input Voltage
Range
+
−
+
−
LOAD
LOAD
t
The equations and graphs for the required external resistor
(R
of ΔVo% is as shown in the next page.
For output adjust down, the allowable output current have
to be the same as nominal output current.
For output adjust up, the allowable output current have to
derate to maximun power.
Refer to the below table
1) PAH75D48-5033 – Output Adjustment
Followings show the equations and graphs for the required
external resistor to tune down and up output voltage for
PAH75D48-5033 standard model.
Ouput
adjust up
Output adjust
down
Nominal output
adj
i) Vo1 (5V): output adjust down
ii) Vo2 (3.3V): output adjust down
) value to obtain a percentage output voltage change
R
adj2
R
adj1
(down) = (
(down) = (
+Vo2
-Vo2
TRM2
+Vo1
-Vo1
TRM1
1000
1000
0.01
100
100
Vo1(V) Io1(A) Vo2(V) Io2(A)
0.1
0.1
10
10
5.5
4.5
1
1
5
5
5
0
0
・All specifications are subject to change without notice.
%CHANGE IN OUTPUT VOLTAGE (Δ%)
%CHANGE IN OUTPUT VOLTAGE (Δ%)
0.256 −ΔVo ( 0.685)
2
2
2.5 −ΔVo (4.32)
4.64
4.11
5.1
5.1
5.1
4
4
ΔVo
ΔVo
Radj2
Radj1
3.63
2.97
6
6
3.3
3.3
3.3
8
8
+
−
+
−
) kΩ
LOAD
LOAD
15
15
15
15
15
10
10
) kΩ
Po(W)
72.45
70.05
75
75
75