PS21267-P Mitsumi Electronics, Corp., PS21267-P Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/4/452/mitsumi_electronics__corp__sml.jpg)
PS21267-P
Manufacturer Part Number
PS21267-P
Description
Manufacturer
Mitsumi Electronics, Corp.
Datasheet
1.PS21267-P.pdf
(10 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PS21267-P/-AP
Manufacturer:
MIT
Quantity:
20 000
Note 1 : To prevent the input signals oscillation, the wiring of each input should be as short as possible. (Less than 2-3cm)
Fig. 10 EXAMPLE OF TYPICAL DIP-IPM APPLICATION CIRCUIT
10 : To prevent IC
2 : By virtue of integrating an application specific type HVIC inside the module, direct coupling to MCU terminals without any opto-coupler
3 : F
4 : F
5 : The logic of input signal is high-active. The DIP-IPM input signal section integrates a 2.5kΩ (min) pull-down resistor. If using external
6 : To prevent malfunction of protection, the wiring of A, B, C should be as short as possible.
7 : Please set the R1C5 time constant in the range 1.5~2µs.
8 : Each capacitor should be located as nearby the pins of the DIP-IPM as possible.
9 : To prevent surge destruction, the wiring between the smoothing capacitor and the P, N1 pins should be as short as possible. Approxi-
or transformer isolation is possible.
resistor.
= 1.8ms (typ.))
RC filter, pay attention to satisfy the turn-on/off threshold voltage requirement.
mately a 0.1~0.22µF snubber capacitor between the P-N1 pins is recommended.
O
O
output is open drain type. This signal line should be pulled up to the positive side of the 5V power supply with approximately 10kΩ
output pulse width is determined by the external capacitor between CFO and V
5V line
15V line
S
from surge destruction, it is recommended to insert a Zener diode (24V, 1W) between each control supply terminals.
C3
C3
C3
C3
C1
C2
C2
C2
C1
C1
The long wiring of GND might generate
noise on input and cause IGBT to
be malfunction.
V
V
V
V
V
V
W
V
V
V
V
V
W
U
U
V
Fo
V
V
VFB
VFS
P1
WFB
WFS
P1
PC
NC
P
UFB
P1
P
P
N
C1:Tight tolerance temp-compensated electrolytic type
C2,C3: 0.22 ~ 2µF R-category ceramic capacitor for noise filtering.
(Note: The capacitance value depends on the PWM control used in the applied system.)
UFS
N1
N
N
V
U
W
F
GND
V
COM
COM
COM
o
V
V
V
CC
N
IN
IN
IN
N
N
CC
CC
CC
HVIC1
HVIC2
HVIC3
LVIC
HO
HO
HO
V
V
V
V
V
V
W
B
S
B
S
B
U
V
CFO
S
CIN
V
OUT
OUT
OUT
NO
CFO
C4(C
A
FO
If this wiring is too long, the SC level
fluctuation might be larger and cause
SC malfunction.
)
CIN
C5
B
NC
DIP-IPM
terminals (C
R1
Shunt
Resistor
N
P
U
V
W
FO
If this wiring is too long,
short circuit might be
caused.
C
TRANSFER-MOLD TYPE
). (Example : C
PS21267-P/AP
N1
INSULATED TYPE
M
FO
= 22nF → t
Oct. 2005
FO