LT1191CS8#PBF Linear Technology, LT1191CS8#PBF Datasheet - Page 9

• Manufacturer Part Number: LT1191CS8#PBF
• Description: IC OP-AMP VIDEO HISPD SNGL 8SOIC
• Manufacturer: Linear Technology

Specifications of LT1191CS8#PBF

• Applications: General Purpose
• Number Of Circuits: 1
• Slew Rate: 450 V/µs
• Current - Supply: 32mA
• Current - Output / Channel: 50mA
• Voltage - Supply, Single/dual (±): 4.75 V ~ 16 V, ±2.38 V ~ 8 V
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

APPLICATIO S I FOR ATIO
Cable Terminations
The LT1191 operational amplifier has been optimized as a
low cost video cable driver. The 50mA guaranteed output
current enables the LT1191 to easily deliver 7.5V
100 , while operating on 5V supplies or 2.6V
single 5V supply.
When driving a cable it is important to terminate the cable
to avoid unwanted reflections. This can be done in one of
two ways: single termination or double termination. With
single termination, the cable must be terminated at the
receiving end (75 to ground) to absorb unwanted en-
ergy. The best performance can be obtained by double
termination (75 in series with the output of the amplifier,
and 75 to ground at the other end of the cable). This
termination is preferred because reflected energy is ab-
sorbed at each end of the cable. When using the double
termination technique it is important to note that the signal
is attenuated by a factor of 2, or 6dB. This can be compen-
sated for by taking a gain of 2, or 6dB in the amplifier. The
cable driver has a –3dB bandwidth of 100MHz while
driving the 150 load. Note the response can be improved
by lowering the impedance of the feedback elements.
Cable Driver Voltage Gain vs Frequency
–10
10
–5
5
0
100k
R
Double Terminated Cable Driver
G
3
2
U
+
LT1191
–
A
R
R
–5V
V
FB
G
A
5V
1M
V
= 2
= 330
4
FREQUENCY (Hz)
7
= 1k
= 1
U
6
R = 1k
R = 1k
G
FB
R
75
FB
10M
R
R
W
FB
G
CABLE
= 300
= 300
V
T
LT1191 • TA08
S
A
75
= 5V
= 25 C
100M
U
P-P
P-P
on a
into
Using the Shutdown Feature
The LT1191 has a unique feature that allows the amplifier
to be shut down for conserving power or for multiplexing
several amplifiers onto a common cable. The amplifier will
shut down by taking Pin 5 to V
dissipates 15mW while maintaining a true high impedance
output state of 15k in parallel with the feedback resis-
tors. The amplifiers must be used in a noninverting con-
figuration for MUX applications. In inverting configurations
the input signal is fed to the output through the feedback
components. The following scope photos show that with
very high R
output slowly decays toward ground. Additionally, when
the output is loaded with as little as 1k the amplifier shuts
off in 400ns. This shutoff can be under the control of HC
CMOS operating between 0V and –5V.
V
V
SHDN
SHDN
V
V
– 5V
– 5V
OUT
OUT
0V
0V
L
, the output is truly high impedance; the
1MHz SINE WAVE GATED OFF WITH
1MHz SINE WAVE GATED OFF WITH
SHUTDOWN PIN, A
SHUTDOWN PIN, A
Output Shutdown
Output Shutdown
–
V
. In shutdown, the amplifier
V
= 1, R
= 1, R
L
L
= 1k
=
LT1191 • TA10
LT1191 • TA09
LT1191
9