LT1195CS8 Linear Technology, LT1195CS8 Datasheet - Page 8
![IC OP-AMP LOW-PWR HI-SPEED 8SOIC](/photos/6/62/66297/8-soic_05-08-1610_sml.jpg)
LT1195CS8
Manufacturer Part Number
LT1195CS8
Description
IC OP-AMP LOW-PWR HI-SPEED 8SOIC
Manufacturer
Linear Technology
Datasheet
1.LT1195CN8.pdf
(12 pages)
Specifications of LT1195CS8
Applications
General Purpose
Number Of Circuits
1
Slew Rate
165 V/µs
Current - Supply
12mA
Current - Output / Channel
20mA
Voltage - Supply, Single/dual (±)
4.75 V ~ 16 V, ±2.38 V ~ 8 V
Mounting Type
Surface Mount
Package / Case
8-SOIC (0.154", 3.90mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LT1195CS8
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT1195CS8#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT1195CS8#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
APPLICATIO S I FOR ATIO
LT1195
Power Supply Bypassing
The LT1195 is quite tolerant of power supply bypassing.
In some applications a 0.1µF ceramic disc capacitor
placed 0.5 inches from the ampifier is all that is required.
In applications requiring good settling time, it is important
to use multiple bypass capacitors. A 0.1µF ceramic disc in
parallel with a 4.7µF tantalum is recommended.
Cable Terminations
The LT1195 operational amplifier has been optimized as a
low cost video cable driver. The ±20mA guaranteed output
current enables the LT1195 to easily deliver 6V
150Ω, while operating on ±5V supplies.
8
When driving a cable it is important to terminate the cable
to avoid unwanted reflections. This can be done in one of
two ways: single termination or double termination. With
single termination, the cable must be terminated at the
–10
–12
R
Cable Driver Voltage Gain vs Frequency
–2
–4
–6
–8
G
8
6
4
2
0
100k
Double-Terminated Cable Driver
V
T
A
S
3
2
= 25°C
= ±5V
+
–
U
LT1195
–5V
1M
5V
FREQUENCY (Hz)
7
4
U
A
R
R
V
FB
G
6
= 1
= 1k
= 1k
10M
R
FB
75Ω
A
R
R
V
FB
G
W
= 2
= 330Ω
= 1k
CABLE
100M
1195 AI02
75Ω
1195 AI01
U
P-P
into
receiving end (75Ω to ground) to absorb unwanted en-
ergy. The best performance can be obtained by double
termination (75Ω in series with the output of the amplifier,
and 75Ω to ground at the other end of the cable). This
termination is preferred because reflected energy is ab-
sorbed at each end of the cable. When using the double
termination technique it is important to note that the signal
is attenuated by a factor of 2, or 6dB. This can be compen-
sated for by taking a gain of 2, or 6dB in the amplifier.
Using the Shutdown Feature
The LT1195 has a unique feature that allows the amplifier
to be shut down for conserving power, or for multiplexing
several amplifiers onto a common cable. The amplifier will
shutdown by taking Pin 5 to V
dissipates 15mW while maintaining a true high impedance
output state of 15k in parallel with the feedback resistors.
The amplifiers must be used in a noninverting configura-
tion for MUX applications. In inverting configurations the
input signal is fed to the output through the feedback
components. The following scope photos show that with
very high R
output slowly decays toward ground. Additionally, when
the output is loaded with as little as 1k the amplifier shuts
off in 700ns. This shutoff can be under the control of HC
CMOS operating between 0V and –5V.
1MHz SINE WAVE GATED OFF WITH SHUTDOWN PIN
A
V
= 1, R
L
L
, the output is truly high impedance; the
= SCOPE PROBE
Output Shutdown
–
. In shutdown, the amplifier
1195 AI03
1195fa