PT8A262P Pericom Semiconductor, PT8A262P Datasheet
PT8A262P
Related parts for PT8A262P
PT8A262P Summary of contents
Page 1
Features 2-stage operational amplifier as filter • • Built-in noise rejection circuit • On-chip regulator • Override function • Synchronous with AC 220V/50Hz and 110V/60Hz • Pulse output (PT8A261) for TRIAC drive or level output (PT8A262) for relay drive ...
Page 2
Pad Location Pad Location of PT8A261DE Die No. Pad Name X Coordinate GND 570 TRIAC 570 OSCD 570 OSCS 570 ZC -378.8 CDS -30.1 MODE 570 V -197 136.9 CC Note: Substrate is connected to GND PT0075(04/03) ...
Page 3
Pad Location of PT8A262DE Die No. Pad Name X Coordinate GND RELAY OSCD OSCS ZC -378.8 CDS -30.1 MODE V -197 136.9 CC Note: Substrate is connected to GND PT0075(04/03) 1470um CDS ZC OSCS MODE V CC ...
Page 4
... Non-inverted input of first operational amplifier, connected directly to source of PIR sensor Inverted input of first operational amplifier Output of first operational amplifier Non-inverted input of second operational amplifier. Inverted input of second operational amplifier Output of second operational amplifier 4 PT8A261/262 PIR Sensor Light Switch Controller PT8A262P/PT8A262W GND 1 16 OP2O 2 15 OP2N 3 ...
Page 5
Functional Descriptions The PT8A261 and PT8A262 are CMOS LSI chips designed for automatic PIR lamp control. They can operate in 2-wire con- figuration for triac applications or in 3-wire configuration for relay applications. The device consists of operational amplifiers, ...
Page 6
MODE MODE is a tri-state input pin for operation mode selection. See the following table 3. Override Control: The term “override” refers to the change of operating mode by switching the power switch twice within 3 seconds. When the ...
Page 7
Power On Initial The PIR signal amplifier requires a warm up period after power- on. The input should be disabled during this period. In the AUTO mode within the first 10 seconds of the initial time the chip allows ...
Page 8
Maximum Ratings (Above which the useful life may be impaired. For user guidelines, not tested) Storage Temperature ............................................................-40 Supply Voltage to Ground Potential (Inputs & V Supply Voltage to Ground Potential (Outputs & D/O Only) -0.3 to +6.0V DC ...
Page 9
AC Electrical Characteristics Voltage Regulator Sym Description V Output Voltage EE V Noninverting input of OP2 OP2P V Line Regulation V Load Regulation LDR I Regulator Output Current L Operational Amplifier and Window Comparator Sym Description BW 3dB Bandwidth ...
Page 10
Oscillator and ZC Input Pulse and Trigger Output Pulse Sym Description f Oscillator Frequency OSC t ZC Pulse Rise Time Pulse Fall Time Pulse Period Pulse Width ZW t TRIAC ...
Page 11
Typical Application Circuits Figure 11. Two-Wire Application Circuit of PT8A261 PT0075(04/03) PIR Sensor Light Switch Controller 11 Data Sheet PT8A261/262 Ver:5 ...
Page 12
Figure 12. Three-Wire Application Circuit of PT8A262 PT0075(04/03) PIR Sensor Light Switch Controller ON AUTO OFF 12 Data Sheet PT8A261/262 Ver:5 ...
Page 13
Email: support@pti.com.cn China: No. 20 Building, 3/F, 481 Guiping Road, Shanghai, 200233, China Tel: (86)-21-6485 0576 Asia Pacific: Unit 1517, 15/F, Chevalier Commercial Centre, 8 Wang Hoi Rd, Kowloon Bay, Hongkong Tel: (852)-2243 3660 U.S.A.: 2380 Bering Drive, San ...