LM6588MTX/NOPB National Semiconductor, LM6588MTX/NOPB Datasheet
LM6588MTX/NOPB
Specifications of LM6588MTX/NOPB
Available stocks
Related parts for LM6588MTX/NOPB
LM6588MTX/NOPB Summary of contents
Page 1
... Supply voltage range n Unity gain stable n −3dB bandwidth (A n Slew rate n Settling time n SO-14 and TSSOP-14 package n Manufactured in National Semiconductor’s state-of-the-art bonded wafer, trench isolated complementary bipolar VIP10 performance at low power levels Applications n LCD panel V n LCD panel gamma buffer ...
Page 2
... Absolute Maximum Ratings If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ESD Tolerance (Note 2) Human Body Model Machine Model + − Supply Voltage ( Differential Input Voltage Output Short Circuit to Ground (Note 3) Storage Temperature Range ...
Page 3
AC Electrical Characteristics Unless otherwise specified, all limits guaranteed for at T perature extremes. Symbol Parameter Unity Gain Bandwidth Product −3dB Frequency Φ Phase Margin m t Settling Time (0.1 Propagation Delay p nd HD2 2 Harmonic ...
Page 4
AC Electrical Characteristics Unless otherwise specified, all limits guaranteed for at T perature extremes. Symbol Parameter SR Slew Rate (Note 9) Unity Gain Bandwidth Product −3dB Frequency Φ Phase Margin m t Settling Time (0.1 Propagation Delay ...
Page 5
Typical Performance Characteristics V = 1/2V and R = 2kΩ Gain Phase vs. Temperature (V Gain Phase vs. Capacitive Loading (V PSRR (V = 5V) S Unless otherwise specified, all limits guaranteed for T = 5V) Gain ...
Page 6
Typical Performance Characteristics V = 1/2V and R = 2kΩ. (Continued CMRR (V = 5V) S Settling Time vs. Input Step Amplitude (Output Slew and Settle Time) Crosstalk Rejection vs. Frequency (Output to Output) www.national.com Unless otherwise ...
Page 7
Typical Performance Characteristics V = 1/2V and R = 2kΩ. (Continued Stability vs. Capacitive Load Unity Gain (V Small Signal Step Response Closed Loop Output Impedance vs. Frequency (A Unless otherwise specified, all limits guaranteed for T ...
Page 8
Typical Performance Characteristics V = 1/2V and R = 2kΩ. (Continued vs. Common Mode Voltage ( from V vs. I OUT I vs. Supply Voltage SUPPLY www.national.com Unless otherwise specified, all limits guaranteed ...
Page 9
Application Notes CIRCUIT DESCRIPTION GENERAL & SPEC The LM6588 is a bipolar process operational amplifier. It has an exceptional output current capability of 200mA. The part has both rail to rail inputs and outputs. It has a −3dB band- width ...
Page 10
Application Notes (Continued) ground is a uniform low impedance four layer board cannot be used, consider pouring a plane on one side of a two layer board. If this cannot be done be sure to use as wide ...
Page 11
TFT Display Application light filter that modulates light transmitted from the back to the front of a display. A pixel’s bottom plate lies on the backside of a display where a light source is applied, and the top plate lies ...
Page 12
TFT Display Application 8KHz to 160KHz, which is much lower than the gain band- width of most op amps result, the V little phase lag when op amp loop gain is unity, and this allows the V Driver ...
Page 13
TFT Display Application GAMMA BUFFER Illumination in a TFT display, also referred to as grayscale, is set by a series of discrete voltage levels that are applied to each LCD pixel. These voltage levels are generated by resistive DAC networks ...
Page 14
TFT Display Application lay and slew limited response time ( calculated from data sheet specifications, the small signal settling time ( cannot. This is because SET amp’s gain vs. frequency ...
Page 15
Physical Dimensions inches (millimeters) unless otherwise noted 14-Pin SOIC NS Package Number M14A 14-Pin TSSOP NS Package Number MTC14 15 www.national.com ...
Page 16
... BANNED SUBSTANCE COMPLIANCE National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ‘‘Banned Substances’’ as defined in CSP-9-111S2. ...