AT32UC3A0128AU Atmel Corporation, AT32UC3A0128AU Datasheet - Page 82
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
AT32UC3A0128AU
Manufacturer Part Number
AT32UC3A0128AU
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT32UC3A0128.pdf
(98 pages)
2.AT32UC3A0128.pdf
(826 pages)
3.AT32UC3A0128.pdf
(377 pages)
4.AT32UC3A0128.pdf
(33 pages)
5.AT32UC3A0128.pdf
(159 pages)
6.AT32UC3A0128AU.pdf
(2 pages)
Specifications of AT32UC3A0128AU
Flash (kbytes)
128 Kbytes
Pin Count
144
Max. Operating Frequency
66 MHz
Cpu
32-bit AVR
# Of Touch Channels
32
Hardware Qtouch Acquisition
No
Max I/o Pins
109
Ext Interrupts
109
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device + OTG
Spi
6
Twi (i2c)
1
Uart
4
Ssc
1
Ethernet
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
384
Resistive Touch Screen
No
Dac Channels
2
Dac Resolution (bits)
16
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
32
Self Program Memory
YES
External Bus Interface
1
Dram Memory
sdram
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
3.0-3.6 or (1.65-1.95+3.0-3.6)
Operating Voltage (vcc)
3.0-3.6 or (1.65-1.95+3.0-3.6)
Fpu
No
Mpu / Mmu
Yes / No
Timers
10
Output Compare Channels
16
Input Capture Channels
6
Pwm Channels
13
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AT32UC3A0128AU-U
Manufacturer:
ATMEL
Quantity:
4
32058KS–AVR32–01/12
15.4.6
15.4.7
15.4.8
15.4.9
15.4.10
15.4.11
PDCA
TWI
SDRAMC
GPIO
USART
Processor and Architecture
1. Wrong PDCA behavior when using two PDCA channels with the same PID.
1. The TWI RXRDY flag in SR register is not reset when a software reset is performed.
1.
1. Some GPIO VIH (input high voltage) are 3.6V max instead of 5V tolerant
1. ISO7816 info register US_NER cannot be read
1. LDM instruction with PC in the register list and without ++ increments Rp
2. RETE instruction does not clear SREG[L] from interrupts.
3.
(data read or code fetch) the second half (last 256 kB) of the flash may fail. This may lead to
an exception or to other errors derived from this corrupted read access.
Fix/Workaround
Flashc WP, EP, EA, WUP, EUP commands: these commands must be issued from RAM or
through the EBI. After these commands, read twice one flash page initialized to 00h in each
half part of the flash.
Workaround/fix
The same PID should not be assigned to more than one channel.
Fix/Workaround
After a Software Reset, the register TWI RHR must be read.
Code execution from SDRAM does not work.
Fix/Workaround
Do not run code from SDRAM.
Only 11 GPIOs remain 5V tolerant (VIHmax=5V):PB01, PB02, PB03, PB10, PB19, PB20,
PB21, PB22, PB23, PB27, PB28.
Workaround/fix
None.
The NER register always returns zero.
Fix/Workaround
None.
For LDM with PC in the register list: the instruction behaves as if the ++ field is always set, ie
the pointer is always updated. This happens even if the ++ field is cleared. Specifically, the
increment of the pointer is done in parallel with the testing of R12.
Fix/Workaround
None.
The RETE instruction clears SREG[L] as expected from exceptions.
Fix/Workaround
When using the STCOND instruction, clear SREG[L] in the stacked value of SR before
returning from interrupts with RETE.
Code execution from external SDRAM does not work
Exceptions when system stack is protected by MPU
AT32UC3A
82