AT32UC3A1256AU Atmel Corporation, AT32UC3A1256AU Datasheet - Page 519

• Manufacturer Part Number: AT32UC3A1256AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A1256AU

• Flash (kbytes): 256 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 69
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32058K AVR32-01/12
Figure 30-20. Example of an OUT Endpoint with 1 Data Bank
Figure 30-21. Example of an OUT Endpoint with 2 Data Banks
30.7.2.13.2 Detailed Description
30.7.2.14
RXOUTI
FIFOCON
RXOUTI
FIFOCON
OUT
OUT
Underflow
(bank 0)
DATA
(bank 0)
DATA
The data is read by the firmware, following the next flow:
If the endpoint uses several banks, the current one can be read by the firmware while the follow-
ing one is being written by the host. Then, when the firmware clears FIFOCON, the following
bank may already be ready and RXOUTI is set immediately.
This error exists only for isochronous IN/OUT endpoints. It raises the Underflow interrupt
(UNDERFI), what triggers an EPXINT interrupt if UNDERFE = 1.
An underflow can occur during IN stage if the host attempts to read from an empty bank. A zero-
length packet is then automatically sent by the USB controller.
•when the bank is full, RXOUTI and FIFOCON are set, what triggers an EPXINT interrupt if
•the firmware acknowledges the interrupt by clearing RXOUTI;
•the firmware can read the byte count of the current bank from BYCT to know how many bytes
•the firmware reads the data from the current bank by using the USB Pipe/Endpoint X FIFO
•the firmware frees the bank and switches to the next bank (if any) by clearing FIFOCON.
RXOUTE = 1;
to read, rather than polling RWALL;
Data register (USB_FIFOX_DATA), until all the expected data frame is read or the bank is
empty (in which case RWALL is cleared by hardware and BYCT reaches 0);
HW
ACK
HW
ACK
SW
read data from CPU
SW
BANK 0
NAK
OUT
read data from CPU
BANK 0
(bank 1)
DATA
SW
OUT
ACK
(bank 0)
DATA
HW
SW
HW
ACK
read data from CPU
SW
read data from CPU
AT32UC3A
BANK 1
SW
BANK 0
519