AT90PWM1 Atmel Corporation, AT90PWM1 Datasheet - Page 107

• Manufacturer Part Number: AT90PWM1
• Manufacturer: Atmel Corporation

Specifications of AT90PWM1

• Flash (kbytes): 8 Kbytes
• Pin Count: 24
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 8
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 19
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 2
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 12
• Input Capture Channels: 1
• Pwm Channels: 7
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

15.7.1
15.8
4378C–AVR–09/08
Modes of Operation
Compare Output Mode and Waveform Generation
Figure 15-5. Compare Match Output Unit, Schematic
The general I/O port function is overridden by the Output Compare (OCnx) from the Waveform
Generator if either of the COMnx1:0 bits are set. However, the OCnx pin direction (input or out-
put) is still controlled by the Data Direction Register (DDR) for the port pin. The Data Direction
Register bit for the OCnx pin (DDR_OCnx) must be set as output before the OCnx value is visi-
ble on the pin. The port override function is generally independent of the Waveform Generation
mode, but there are some exceptions. Refer to
The design of the Output Compare pin logic allows initialization of the OCnx state before the out-
put is enabled. Note that some COMnx1:0 bit settings are reserved for certain modes of
operation.
The COMnx1:0 bits have no effect on the Input Capture unit.
The Waveform Generator uses the COMnx1:0 bits differently in normal, CTC, and PWM modes.
For all modes, setting the COMnx1:0 = 0 tells the Waveform Generator that no action on the
OCnx Register is to be performed on the next compare match. For compare output actions in the
non-PWM modes refer to
117, and for phase correct and phase and frequency correct PWM refer to
117.
A change of the COMnx1:0 bits state will have effect at the first compare match after the bits are
written. For non-PWM modes, the action can be forced to have immediate effect by using the
FOCnx strobe bits.
The mode of operation, i.e., the behavior of the Timer/Counter and the Output Compare pins, is
defined by the combination of the Waveform Generation mode (WGMn3:0) and Compare Output
mode (COMnx1:0) bits. The Compare Output mode bits do not affect the counting sequence,
while the Waveform Generation mode bits do. The COMnx1:0 bits control whether the PWM out-
COMnx1
COMnx0
FOCnx
clk
I/O
See “16-bit Timer/Counter Register Description” on page 116.
Waveform
Generator
Table 29 on page
D
D
D
PORT
DDR
OCnx
117. For fast PWM mode refer to
Table
Q
Q
Q
29,
Table 30
1
0
and
Table 31
AT90PWM1
Table 31 on page
Table 30 on page
for details.
OCnx
Pin
107