ATmega169PA Atmel Corporation, ATmega169PA Datasheet - Page 36

no-image

ATmega169PA

Manufacturer Part Number
ATmega169PA
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATmega169PA

Flash (kbytes)
16 Kbytes
Pin Count
64
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
54
Ext Interrupts
17
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Segment Lcd
100
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
1
Eeprom (bytes)
512
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
4
Input Capture Channels
1
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATmega169PA-AN
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega169PA-ANR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega169PA-AU
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega169PA-AU
Manufacturer:
ATMEL
Quantity:
8 000
Part Number:
ATmega169PA-AUR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega169PA-MU
Manufacturer:
ATMEL
Quantity:
31
Part Number:
ATmega169PAAU
Manufacturer:
INF
Quantity:
4 275
9.8
8284D–AVR–6/11
Clock Output Buffer
ATmega169A/PA/329A/PA/3290A/PA/649A/P/6490A/P
Figure 9-3.
When this clock source is selected, start-up times are determined by the SUT Fuses as shown in
Table
Table 9-12.
Table 9-13.
When applying an external clock, it is required to avoid sudden changes in the applied clock fre-
quency to ensure stable operation of the MCU. A variation in frequency of more than 2% from
one clock cycle to the next can lead to unpredictable behavior. It is required to ensure that the
MCU is kept in Reset during such changes in the clock frequency.
Note that the System Clock Prescaler can be used to implement run-time changes of the internal
clock frequency while still ensuring stable operation. Refer to
37
When the CKOUT Fuse is programmed, the system Clock will be output on CLKO. This mode is
suitable when the chip clock is used to drive other circuits on the system. The clock will be out-
put also during reset and the normal operation of I/O pin will be overridden when the fuse is
programmed. Any clock source, including internal RC Oscillator, can be selected when CLKO
serves as clock output. If the System Clock Prescaler is used, it is the divided system clock that
is output when the CKOUT Fuse is programmed.
ATmega169A/169PA/649A/649P
ATmega329A/329PA/3290A/3290PA/6490A/6490P
SUT1..0
for details.
00
01
10
11
9-13.
Start-up Time from Power-
External Clock Drive Configuration
Crystal Oscillator Clock Frequency
Start-up Times for the External Clock Selection
down and Power-save
6 CK
6 CK
6 CK
EXTERNAL
SIGNAL
CLOCK
NC
Additional Delay from
Reset (V
Reserved
14CK + 4.1ms
CKSEL3:0
0000
0000
14CK + 65ms
XTAL2
XTAL1
GND
14CK
CC
= 5.0V)
”System Clock Prescaler” on page
Frequency Range
0 - 16MHz
0 - 20MHz
BOD enabled
Fast rising power
Slowly rising power
Recommended Usage
36

Related parts for ATmega169PA