ATmega88 Atmel Corporation, ATmega88 Datasheet - Page 23

• Manufacturer Part Number: ATmega88
• Manufacturer: Atmel Corporation

Specifications of ATmega88

• Flash (kbytes): 8 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 23
• Ext Interrupts: 24
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

11. Errata
11.1
11.1.1
11.1.2
11.1.3
2545TS–AVR–05/11
Errata Atmel ATmega48
Rev. D
Rev. C
Rev. B
The revision letter in this section refers to the revision of the ATmega48 device.
•
1. Interrupts may be lost when writing the timer registers in the asynchronous timer
•
•
1.
2. Interrupts may be lost when writing the timer registers in the asynchronous timer
•
1. Interrupts may be lost when writing the timer registers in the asynchronous timer
Interrupts may be lost when writing the timer registers in the asynchronous timer
Reading EEPROM when system clock frequency is below 900kHz may not work
Interrupts may be lost when writing the timer registers in the asynchronous timer
Interrupts may be lost when writing the timer registers in the asynchronous timer
The interrupt will be lost if a timer register that is synchronous timer clock is written when the
asynchronous Timer/Counter register (TCNTx) is 0x00.
Problem fix/workaround
Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor
0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous
Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx).
Reading EEPROM when system clock frequency is below 900kHz may not work
Reading Data from the EEPROM at system clock frequency below 900kHz may result in
wrong data read.
Problem fix/workaround
Avoid using the EEPROM at clock frequency below 900kHz.
The interrupt will be lost if a timer register that is synchronous timer clock is written when the
asynchronous Timer/Counter register (TCNTx) is 0x00.
Problem fix/workaround
Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor
0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous
Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx).
The interrupt will be lost if a timer register that is synchronous timer clock is written when the
asynchronous Timer/Counter register (TCNTx) is 0x00.
Problem fix/workaround
Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor
0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous
Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx).
ATmega48/88/168
23