ATtiny261A Atmel Corporation, ATtiny261A Datasheet - Page 3

• Manufacturer Part Number: ATtiny261A
• Manufacturer: Atmel Corporation

Specifications of ATtiny261A

• Flash (kbytes): 2 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 4
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.12
• Eeprom (bytes): 128
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

1.1
1.1.1
1.1.2
1.1.3
1.1.4
1.1.5
1.1.6
1.1.7
8197CS–AVR–05/11
Pin Descriptions
VCC
GND
AVCC
AGND
Port A (PA7:PA0)
Port B (PB7:PB0)
RESET
Supply voltage.
Ground.
Analog supply voltage. This is the supply voltage pin for the Analog-to-digital Converter (ADC),
the analog comparator, the Brown-Out Detector (BOD), the internal voltage reference and Port
A. It should be externally connected to VCC, even if some peripherals such as the ADC are not
used. If the ADC is used AVCC should be connected to VCC through a low-pass filter.
Analog ground.
An 8-bit, bi-directional I/O port with internal pull-up resistors, individually selectable for each bit.
Output buffers have symmetrical drive characteristics with both high sink and source capability.
As inputs, port pins that are externally pulled low will source current if pull-up resistors have
been activated. Port pins are tri-stated when a reset condition becomes active, even if the clock
is not running.
Port A also serves the functions of various special features of the device, as listed on
An 8-bit, bi-directional I/O port with internal pull-up resistors, individually selectable for each bit.
Output buffers have symmetrical drive characteristics with both high sink and source capability.
As inputs, port pins that are externally pulled low will source current if pull-up resistors have
been activated. Port pins are tri-stated when a reset condition becomes active, even if the clock
is not running.
Port B also serves the functions of various special features of the device, as listed on
Reset input. A low level on this pin for longer than the minimum pulse length will generate a
reset, even if the clock is not running and provided the reset pin has not been disabled. The min-
imum pulse length is given in
generate a reset.
The reset pin can also be used as a (weak) I/O pin.
Table 19-4 on page
ATtiny261A/461A/861A
188. Shorter pulses are not guaranteed to
page
page
62.
65.
3