ATUC128L4U Atmel Corporation, ATUC128L4U Datasheet - Page 78
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATUC128L4U
Manufacturer Part Number
ATUC128L4U
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT32UC3A0128.pdf
(377 pages)
2.AT32UC3A0128.pdf
(159 pages)
3.ATUC128L4U.pdf
(960 pages)
4.ATUC128L4U.pdf
(92 pages)
Specifications of ATUC128L4U
Flash (kbytes)
128 Kbytes
Pin Count
48
Max. Operating Frequency
50 MHz
Cpu
32-bit AVR
# Of Touch Channels
17
Hardware Qtouch Acquisition
Yes
Max I/o Pins
36
Ext Interrupts
36
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
1
Twi (i2c)
2
Uart
4
Lin
4
Ssc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
12
Adc Speed (ksps)
460
Analog Comparators
8
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
No
Sram (kbytes)
16
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.62 to 3.6
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
Yes / No
Timers
6
Output Compare Channels
18
Input Capture Channels
12
Pwm Channels
35
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATUC128L4U-U
Manufacturer:
ATMEL
Quantity:
3 006
10.1.6
10.2
10.2.1
32142AS–12/2011
Rev. B
aWire
SCIF
2. Autonomous CAT acquisition must be longer than AST source clock period
1. aWire MEMORY_SPEED_REQUEST command does not return correct CV
1. The RC32K output on PA20 is not always permanently disabled
2. PLLCOUNT value larger than zero can cause PLLEN glitch
3. Writing 0x5A5A5A5A to the SCIF memory range will enable the SCIF UNLOCK feature
eral bus clock, where n is the ratio of the PB clock frequency to the GCLK_CAT frequency.
This results in premature loss of charge from the sense capacitors and thus increased vari-
ability of the acquired count values.
Fix/Workaround
Enable the 1kOhm drive resistors on all implemented QMatrix Y lines (CSA 1, 3, 5, 7, 9, 11,
13, and/or 15) by writing ones to the corresponding odd bits of the CSARES register.
When using the AST to trigger CAT autonomous touch acquisition in sleep modes where the
CAT bus clock is turned off, the CAT will start several acquisitions if the period of the AST
source clock is larger than one CAT acquisition. One AST clock period after the AST trigger,
the CAT clock will automatically stop and the CAT acquisition can be stopped prematurely,
ruining the result.
Fix/Workaround
Always ensure that the ATCFG1.max field is set so that the duration of the autonomous
touch acquisition is greater than one clock period of the AST source clock.
The aWire MEMORY_SPEED_REQUEST command does not return a CV corresponding to
the formula in the aWire Debug Interface chapter.
Fix/Workaround
I s s u e a d u m m y r e a d t o a d d r e s s 0 x 1 0 0 0 0 0 0 0 0 b e f o r e i s s u i n g t h e
MEMORY_SPEED_REQUEST command and use this formula instead:
The RC32K output on PA20 may sometimes re-appear.
Fix/Workaround
Before using RC32K for other purposes, the following procedure has to be followed in order
to properly disable it:
- Run the CPU on RCSYS
- Disable the output to PA20 by writing a zero to PM.PPCR.RC32OUT
- Enable RC32K by writing a one to SCIF.RC32KCR.EN, and wait for this bit to be read as
one
- Disable RC32K by writing a zero to SCIF.RC32KCR.EN, and wait for this bit to be read as
zero.
Initializing the PLLCOUNT with a value greater than zero creates a glitch on the PLLEN sig-
nal during asynchronous wake up.
Fix/Workaround
The lock-masking mechanism for the PLL should not be used.
The PLLCOUNT field of the PLL Control Register should always be written to zero.
f
sab
=
---------------- -
CV 3
7f
aw
–
ATUC64/128/256L3/4U
78