SAM7S128 Atmel Corporation, SAM7S128 Datasheet - Page 617

• Manufacturer Part Number: SAM7S128
• Manufacturer: Atmel Corporation

Specifications of SAM7S128

• Flash (kbytes): 128 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 55 MHz
• Cpu: ARM7TDMI
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 32
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 1
• Twi (i2c): 1
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 32
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: No

40.6.7
40.6.7.1
40.6.7.2
40.6.7.3
40.6.7.4
6175L–ATARM–28-Jul-11
Pulse Width Modulation Controller (PWM)
PWM: Counter Start Value
PWM: Constraints on Duty Cycle Value
PWM: Update when PWM_CCNTx = 0 or 1
PWM: Update when PWM_CPRDx = 0
Note:
When changing CSS in the PMC_MCKR to switch from
Ensure that the processor is executing out of SRAM and ensure no transition occurs on PA1,
either as an input or output, starting from writing to the PMC_MCKR register until MCKRDY = 1.
If the Channel Counter Register value is 0 or 1, the Channel Period Register or Channel Duty
Cycle Register is directly modified when writing the Channel Update Register.
Check the Channel Counter Register before writing the update register.
When Channel Period Register equals 0, the period update is not operational.
Do not write 0 in the period register.
In left aligned mode, the first start value of the counter is 0. For the other periods, the counter
starts at 1.
None.
Setting Channel Duty Cycle Register (PWM_CDTYx) at 0 in center aligned mode or at 0 or 1 in
left aligned mode may change the polarity of the signal.
Do not set PWM_CDTYx at 0 in center aligned mode.
Do not set PWM_CDTYx at 0 or 1 in left aligned mode.
1. Switching from:
2. Program code is being executed out of flash, or a transition is occurring on PA1, either
And
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
Problem Fix/Workaround
– PLL Clock to Slow Clock or
– PLL Clock to Main Clock or
– Main Clock to PLL Clock or
– Main Clock to Slow Clock
as an input or output.
– PLL Clock to Slow Clock or
– PLL Clock to Main Clock or
– Main Clock to PLL Clock or
– Main Clock to Slow Clock
This issue does not occur when transitioning from slow clock to main clock or from slow clock to
PLL clock.
SAM7S Series
617