AT32UC3C1512C Automotive Atmel Corporation, AT32UC3C1512C Automotive Datasheet - Page 23
AT32UC3C1512C Automotive
Manufacturer Part Number
AT32UC3C1512C Automotive
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT90CAN128_AUTOMOTIVE.pdf
(225 pages)
2.AT32UC3C0512C_AUTOMOTIVE.pdf
(1312 pages)
3.AT32UC3C0512C_AUTOMOTIVE.pdf
(107 pages)
- AT90CAN128_AUTOMOTIVE PDF datasheet
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #2
- AT32UC3C0512C_AUTOMOTIVE PDF datasheet #3
- Current page: 23 of 225
- Download datasheet (4Mb)
7701E–AVR–02/11
• Bit 7 – Res: Reserved Bit
This bit is reserved for future use, and will always read as 0 in Atmel
compatibility with future AVR
mask out this bit.
• Bit 6 – Res: Reserved Bit
This bit is reserved in the Atmel ATtiny24/44/84 and will always read as zero.
• Bits 5, 4 – EEPM1 and EEPM0: EEPROM Mode Bits
The EEPROM programming mode bits define which programming action will be triggered
when writing EEPE. It is possible to program data in one atomic operation (erase the old value
and program the new value) or split the erase and write operations into two separate opera-
tions. The programming times for the different modes are shown in Table 6-1. While EEPE is
set, any write to EEPMn will be ignored. During reset, the EEPMn bits will be reset to 0b00
unless the EEPROM is busy programming.
Table 6-1.
• Bit 3 – EERIE: EEPROM Ready Interrupt Enable
Writing EERIE to logical one enables the EEPROM ready interrupt if the I-bit in SREG is set.
Writing EERIE to logical zero disables the interrupt. The EEPROM ready interrupt generates a
constant interrupt when non-volatile memory is ready for programming.
• Bit 2 – EEMPE: EEPROM Master Program Enable
The EEMPE bit determines whether writing EEPE to logical one will have effect or not. When
EEMPE is set, setting EEPE within four clock cycles will program the EEPROM at the selected
address. If EEMPE is logical zero, setting EEPE will have no effect. When EEMPE has been
written to logical one by software, hardware clears the bit to logical zero after four clock cycles.
• Bit 1 – EEPE: EEPROM Program Enable
The EEPROM program enable bit, EEPE, is the programming enable signal to the EEPROM.
When EEPE is written, the EEPROM will be programmed according to the EEPMn bits setting.
The EEMPE bit must be written to logical one before a logical one is written to EEPE, other-
wise no EEPROM write will take place. When the write access time has elapsed, the EEPE bit
is cleared by hardware. When EEPE has been set, the CPU is halted for two cycles before the
next instruction is executed.
EEPM1
0
0
1
1
EEPM0
EEPROM Mode Bits
0
1
0
1
Programming
Atmel ATtiny24/44/84 [Preliminary]
3.4ms
1.8ms
1.8ms
Time
–
®
devices, always write this bit to a logical zero. After reading,
Operation
Erase and Write in one operation (Atomic Operation)
Erase Only
Write Only
Reserved for future use
®
ATtiny24/44/84. For
23
Related parts for AT32UC3C1512C Automotive
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: