SAM3N00A Atmel Corporation, SAM3N00A Datasheet - Page 24
SAM3N00A
Manufacturer Part Number
SAM3N00A
Description
Manufacturer
Atmel Corporation
- Current page: 24 of 752
- Download datasheet (17Mb)
Table 6-1.
Notes:
6.2.1
24
SYSTEM_IO
bit number
1. If PB12 is used as PIO input in user applications, a low level must be ensured at startup to prevent Flash erase before the
2. In the product Datasheet Refer to: Slow Clock Generator of the Supply Controller section.
3. In the product Datasheet Refer to: 3 to 20 MHZ Crystal Oscillator information in the PMC section.
12
SAM3N
7
6
5
4
-
-
-
-
Serial Wire JTAG Debug Port (SWJ-DP) Pins
user application sets PB12 into PIO mode.
System I/O Configuration Pin List.
TDO/TRACESWO
Default function
TCK/SWCLK
The SWJ-DP pins are TCK/SWCLK, TMS/SWDIO, TDO/SWO, TDI and commonly provided on
a standard 20-pin JTAG connector defined by ARM. For more details about voltage reference
and reset state, refer to
At startup, SWJ-DP pins are configured in SWJ-DP mode to allow connection with debugging
probe. Please refer to the “Debug and Test” section of the product datasheet.
SWJ-DP pins can be used as standard I/Os to provide users more general input/output pins
when the debug port is not needed in the end application. Mode selection between SWJ-DP
mode (System IO mode) and general IO mode is performed through the AHB Matrix Special
Function Registers (MATRIX_SFR). Configuration of the pad for pull-up, triggers, debouncing
and glitch filters is possible regardless of the mode.
The JTAGSEL pin is used to select the JTAG boundary scan when asserted at a high level. It
integrates a permanent pull-down resistor of about 15 kΩ to GND, so that it can be left uncon-
nected for normal operations.
By default, the JTAG Debug Port is active. If the debugger host wants to switch to the Serial
Wire Debug Port, it must provide a dedicated JTAG sequence on TMS/SWDIO and
TCK/SWCLK which disables the JTAG-DP and enables the SW-DP. When the Serial Wire
Debug Port is active, TDO/TRACESWO can be used for trace.
The asynchronous TRACE output (TRACESWO) is multiplexed with TDO. So the asynchronous
trace can only be used with SW-DP, not JTAG-DP. For more information about SW-DP and
JTAG-DP switching, please refer to the” Debug and Test” section.
TMS/SWDIO
after reset
ERASE
PB9
PB8
PA7
PA8
TDI
Other function
XOUT32
Table 3-1 on page
PB12
XIN32
XOUT
PB7
PB6
PB5
PB4
XIN
Constraints for
6.
normal start
Low Level at
startup
-
-
-
-
-
-
-
-
(1)
In Matrix User Interface Registers
Configuration Register in the Bus
Matrix section of the product
(Refer to the System I/O
See footnote
See footnote
Configuration
datasheet.)
11011A–ATARM–04-Oct-10
(2)
(3)
below
below
Related parts for SAM3N00A
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Cortex M3 Flash Microcontroller Converges Performance and Simplicity
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: