1934287-1 TE Connectivity, 1934287-1 Datasheet - Page 6

• Manufacturer Part Number: 1934287-1
• Manufacturer: TE Connectivity

Specifications of 1934287-1

• Connector Type: Header
• Pcb Mounting Orientation: Vertical
• Pcb Mount Retention: With
• Termination Method To Pc Board: Through Hole - Press Fit
• Pcb Mount Alignment: Without
• Sealed: No
• Ul File Number: E28476
• Stackable: No
• Module Type: Center
• Data Rate (gb/s): 10.000
• Differential Impedance (?): 100
• Contact - Rated Current (a): 0.5
• Hot Pluggable: No
• Operating Voltage Reference: AC
• Operating Voltage (vac): 250
• Tail Length (mm [in]): 2.5 [0.098]
• Header Type: Partially Shrouded
• Number Of Positions: 210
• Number Of Signal Positions: 140
• Number Of Rows: 15
• Number Of Columns: 14
• Pcb Mount Retention Type: Compliant Posts
• Centerline (mm [in]): 1.91 [0.075]
• Row-to-row Spacing (mm [in]): 1.40 [0.055]
• Mating Retention: Without
• Contact Type: Pin
• Contact Design: Rectangular Post
• Contact Base Material: Phosphor Bronze
• Contact Plating, Mating Area, Material: Gold
• Contact Plating, Mating Area, Thickness (µm [?in]): 0.76 [29.92]
• Tail Plating Material: Matte Tin
• Tail Plating, Thickness (µm [?in]): 0.5 [20]
• Connector Style: Plug
• End Wall Location: Open
• Housing Color: Black
• Mating Alignment: With
• Mating Alignment Type: Guide Slot
• Housing Material: Liquid Crystal Polymer (LCP)
• Ul Flammability Rating: UL 94V-0
• Number Of Pairs Per Connector: 70
• Pairs Per Column: 5
• Differential Signaling: With
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was RoHS compliant
• Agency/standard: UL
• Ul Rating: Recognized
• Ul Voltage Rating (vac): 250
• Operating Temperature (°c [°f]): -65 – +90 [-85 – +194]
• Board-to-board Configuration: Right Angle
• Pcb Thickness, Recommended (mm [in]): 1.57 [0.062]
• Contact Transmits (typical Application): Signal (Data)
• Packaging Method: Tube

4.
4.1.
4.2.
4.3.
4.4.
Rev B
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
B.
Requalification Testing
If changes significantly affecting form , fit or function are m ade to the product or m anufacturing process,
product assurance shall coordinate requalification testing, consisting of all or part of the original testing
sequence as determ ined by developm ent/product, quality and reliability engineering.
Acceptance
Acceptance is based on verification that the product m eets the requirem ents of Figure 1. Failures
attributed to equipm ent, test setup or operator deficiencies shall not disqualify the product. If product
failure occurs, corrective action shall be taken and specim ens resubm itted for qualification. Testing to
confirm corrective action is required before resubm ittal.
Quality Conform ance Inspection
The applicable quality inspection plan shall specify the sam pling acceptable quality level to be used.
Dim ensional and functional requirem ents shall be in accordance with the applicable product drawing
and this specification.
Specim en Selection
Specim ens shall be prepared in accordance with applicable Instruction Sheets and shall be
selected at random from current production. Each test group shall consist of a m inim um of 3
specim ens.
Test Sequence
Qualification inspection shall be verified by testing specim ens as specified in Figure 2.
108-2303
6 of 8