1-644894-4 TE Connectivity, 1-644894-4 Datasheet - Page 5

• Manufacturer Part Number: 1-644894-4
• Manufacturer: TE Connectivity

Specifications of 1-644894-4

• Connector Type: Header
• Product Line: CST-100
• Pcb Mounting Orientation: Right Angle
• Right Angle Bending Side: Front
• Pcb Mount Retention: Without
• Mating Connector Lock: Without
• Four Points Of Contact: Without
• Shrouded: Yes
• Mounting Ears: Without
• Post Size (mm [in]): 0.64 [.025]
• Panel Mount Retention: Without
• Voltage Rating (vac): 250
• Solder Tail Contact Plating: Matte Tin-Lead
• Termination Post Length (mm [in]): 3.56 [0.140]
• Number Of Positions: 14
• Centerline (mm [in]): 2.54 [0.100]
• Solder Tail Contact Material: Copper Alloy
• Recycle: Yes
• Contact Type: Pin
• Contact Shape: Square
• Contact Plating, Mating Area, Material: Tin-Lead
• Contact Base Material: Copper Alloy
• Connector Style: Plug
• Housing Color: Black
• Mating Alignment: Without
• Ul Flammability Rating: UL 94V-0
• Housing Material: Polyester
• Backwall/post Interruption(s): Without
• Rohs/elv Compliance: Not ELV/RoHS compliant
• Lead Free Solder Processes: Wave solder capable to 240°C
• Applies To: Printed Circuit Board
• Application Use: Wire-to-Board

4.
4.1.
4.2.
4.3.
4.4.
Rev C
QUALITY ASSURANCE PROVISIONS
Qualification Testing
A.
B.
Requalification Testing
If changes significantly affecting form, fit or function are made to the product or manufacturing process,
product assurance shall coordinate requalification testing, consisting of all or part of the original testing
sequence as determined by development/product, quality and reliability engineering.
Acceptance
Acceptance is based on verification that the product meets the requirements of Figure 1. Failures
attributed to equipment, test setup or operator deficiencies shall not disqualify the product. If product
failure occurs, corrective action shall be taken and specimens resubmitted for qualification. Testing to
confirm corrective action is required before resubmittal.
Quality Conformance Inspection
The applicable quality inspection plan will specify the sampling acceptable quality level to be used.
Dimensional and functional requirements shall be in accordance with the applicable product drawing
and this specification.
Specimen Selection
Specimens shall be prepared in accordance with applicable Instruction Sheets and shall be
selected at random from current production. Test groups 1, 2, 3 and 4 shall each consist of a
minimum of 5 connector assemblies with a minimum of 30 data points. Test group 5 shall consist
of a minimum of 5 headers with a minimum of 30 header posts. Test group 6 shall consist of 25
specimens of each wire size. Specimens for additional testing in test group 1 shall consist of 24, 6
position assemblies with the following plating configurations for CST-100 contact to header: 30 µin
Au to 30 µin Au; 30 µin Au to 30 µin PdNi; 30 µin PdNi to 30 µin Au; and 30 µin PdNi to 30 µin
PdNi. Specimens for additional testing in test group 4 shall consist of 24, 6 position assemblies
with the following plating configurations for CST-100 contact to header: 30 µin Au to 30 µin Au; 30
µin Au to 30 µin PdNi; 30 µin PdNi to 30 µin Au; 30 µin PdNi to 30 µin PdNi; 15 µin Au to 15 µin Au;
15 µin Au to 15 µin PdNi; 15 µin PdNi to 15 µin Au; and 15 µin PdNi to 15 µin PdNi.
Test Sequence
Qualification inspection shall be verified by testing specimens as specified in Figure 2.
108-1328
5 of 8