5-353293-3 TE Connectivity, 5-353293-3 Datasheet
5-353293-3
Specifications of 5-353293-3
Available stocks
Related parts for 5-353293-3
5-353293-3 Summary of contents
Page 1
... Scope: 1.1 Contents: This specification covers the requirements for product performance, test methods and quality assurance provisions of AMP Mini Common Termination (CT) Connector 1.5mm Pitch (MT Type). Applicable product description and part numbers are as shown in Fig.1. 2. Applicable Documents: The following documents form a part of this specification to the extent specified herein. In the event of conflict between the requirements of this specification and the product drawing, the product drawing shall take precedence ...
Page 2
... Holder Housing for Double Row Housing : 66 Nylon NON G.F.(UL94V-O) Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Pre tin-Lead plated Brass (0.8µm min .thick tin-lead plating over 0.5µm min.thick (3µm min thick tin-lead plating over 3µm min.thick copper underplating) PAGE Document No. ...
Page 3
... Applicable Panel Thickness 0.8~ 1.6mm (To be used for post header assembly relay) 3.7 Performance Requirements and Test Descriptions : The product shall be designed to meet the electrical, mechanical and environmental performance requirements specified in Fig.2. ...
Page 4
... Fig.4. 500 VAC for 1 minute. Test between adjacent circuits of mated connectors. MIL STD 202 TEST METHOD 301 Impressed voltage 500 VDC for 1 minute. Test between adjacent circuits of mated connectors. MIL STD 202 TEST METHOD 302 CONDITION A Contacts series-wired,apply test current of loaded rating ...
Page 5
... Fig.5 Measure post retention force. Operation Speed : 50 mm/min. Fig.6 Apply an axial pull-off load to crimped wire. Operation Speed : 50 mm/min. Measure panel retention force using panel of nominal cut-out dimensions as specified in the drawing. Loading is made from the punch entering direction of the cut-out hole.See Fig.7 ...
Page 6
... Max.(Final) Wet Solder Coverage : 90 % Min. Fig. 2 (To be continued) PAGE Document No Procedures Subject mated connectors to 10-55-10 Hz traversed in 1 minute at 1.52 mm amplitude 2 hours each of 3 mutually perpendicular planes applied. MIL-STD-202 TEST METHOD 201 CONDITION A IEC 68-2-6 Mounting : Fig. 9 Accelerated Velocity : ...
Page 7
... Temperature:350 ± 10 ℃ for 3+1 -0 Seconds damage by the top of iron. at soldering tynes. Environmental Requirements 20 mΩ Max. (Final) Mated connector - 55 ° min.,+85 ° min. Making this a cycle, repeat 500cycles. IEC 68-2-14 Insulation resistance Mated connector,90~ 95 %R.H. 100 MΩ Min.(Final) 40 °C,500 hours ...
Page 8
... Max. (Final) Mated connector - 40 ± 3 °C, 500 hours IEC 68-2-1 20 mΩ Max. (Final) Mated connector SO2 Gas : 10 ± 3 ppm R.H. 35 ± 2 °C, 240 hours 20 mΩ Max. (Final) Mated connector H2S Gas : 3 ppm,40 ± 3 ℃ R.H.、 240 hours 20 mΩ ...
Page 9
... Industrial Ammonia Gas Resistance to Solvent (a) Numbers indicate sequence in which the tests are performed. Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Test Group Test Sequence (a) 1,6 1,3 1,3 1,3 1,3 1,3 1,3 1,3 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 2 Fig.3 (To be continued) PAGE Document No. 108-5525 ...
Page 10
... Gas 2 Industrial H S Gas 2 Industrial Ammonia Gas Resistance to Solvent (a) Numbers indicate sequence in which the tests are performed. Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Test Group Test Sequence (a) 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 2,4 2,4 2,4 2,4 2,4 2,4 2,4 2 Fig.3 (End) PAGE Document No. 108-5525 ...
Page 11
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig. 4 Fig. 5 Fig. 6 PAGE Document No. 108-5525 REV LOC A ES ...
Page 12
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig. 7 Fig. 8 PAGE Document No. 108-5525 REV LOC A ES ...
Page 13
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig. 10 PAGE Document No. 108-5525 REV LOC A ES ...
Page 14
... Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Fig. 11 PAGE Document No. 108-5525 REV LOC A ES ...
Page 15
... Note : To be applied same specification to post header relay panel mount type by measurement on opposite lock side. Tyco Electronics AMP Shanghai Ltd. ASHL-0005- ES REV B Unmating Force N (kgf) min. 2.99 ) 4.508 ( 0.46 3.26 ) 5.194 ( 0 ...
Page 16
... Single Row Post Header Assembly (V) DIP Staggered Type With Boss With Kink 2~ 20 Pos. Single Row Post Header Assembly(V) DIP Staggered Type Without Boss Without Kink 2~ 20 Pos. Tube Packing for Single Row Post Header Assembly (V) DIP Staggered Type Without Boss Without Kink 2~ 20 Pos. ...
Page 17
... Type Without Boss 2~ 20 Pos. Duble Row Post Header Assembly (V) DIP Staggered Type With Boss With Kink 22~ 40 Pos.(Only Even Number Pos.) Double Row Post Header Assembly (V) SMT Type With Boss 22~ 40 Pos.(Only Even Number Pos.) Double Row Post Header Assembly Panel Mount Type 22~ ...