3-178139-5 TE Connectivity, 3-178139-5 Datasheet
3-178139-5
Specifications of 3-178139-5
Related parts for 3-178139-5
3-178139-5 Summary of contents
Page 1
... TE Specifications : A. 114-5148 : Application Specification B. 501-5013, 501-78324 : Qualification Test Report 2.2 Commercial Standards and Specifications : A. MIL-STD-202 : Test Methods for Electronic and B. EIA-364 : Electrical Connector / Socket Test Procedures Including Enveronmental Classifications 3. Requirements: 3.1 Design and Construction : Product shall be of the design, construction and physical dimensions specified on the applicable product drawing ...
Page 2
... All tests shall be performed in the room temperature, unless otherwise specified. : Nickel plating all over Rec : Gold plating(Contact Area) or Tin-plating(All over) Tin-plating(Tine Area) or Tin-plating(All over) Tin-plating(All over) : Tin plating 250V AC/DC(for 3.81 mm pitch Connector) 600V AC/DC(for 5.08 mm pitch Connector) maximum allowable current to be applied. #24 #26 # ...
Page 3
... Test Requirements and Procedures Summary 項目 試験項目 Para. Test Items 3.5.0 製品の確認 3.5.0 Examination of Product 3.5.1 総合抵抗 (ローレベル) 3 ...
Page 4
... MIL-STD-202,試験法213,条件 electrical discontinuity Accelerated Velocity :490 m/s greater than 1 μs. Waveform Shall occur. Duration Termination Resistance Number of Drops : 3 drops each to normal (Low Level) and reversed directions and Z axes, totally 18 drops. EIA364-27B Method A MIL-STD-202,Method213,Condition A 108-5349 試 ...
Page 5
... Measure the force required to insert Per 1 contact contact into housing. 振動中1μs. をこえる不連続導 振動周波数 : 10~500Hz / 15 min 通を生じないこと。 加速度 振動方向 ...
Page 6
... EIA364-52 MIL-STD-202 試験法208 Wet Solder Coverage : Solder Temperature : ...
Page 7
... MIL-STD-202 試験法107 条件 A-1 Termination Resistance Mated/Unmated connector (Low Level) -55° min.,+85° min. Making this a cycle, repeat 25 cycles. EIA364-32 MIL-STD-202 Method 107 Condition A-1 試験後、絶縁抵抗、耐電圧及び ...
Page 8
... Termination Resistance Subject mated connectors salt (Low Level) concentration for 96h : EIA364-26B Condition A MIL-STD-202 Method 101 Condition A Fig. 3 (終り) Fig. 3 (End) 108-5349 試 験 方 法 Procedures ガス 10±3 ppm Gas : 10±3 ppm ...
Page 9
... Rev. J5 Product Specification 製品規格 Fig.4 Fig.5 108-5349 ...
Page 10
... Temperature Life 塩水噴霧 Salt Spray (a) 欄内の数字は試験の順序を示す。/Numbers indicate sequence in which the tests are performed. Rev. J5 Product Specification 製品規格 ...
Page 11
... Pressure 4.2 製品再認定試験 もし製品に、形状、組合せや嵌合、又は機能に 相当の影響を及ぼす変更がなされた時には、品 ...
Page 12
... Rev. J5 Product Specification 製品規格 4.3 Acceptance: Acceptance is based on verification that the product meets the requirements of Figure.3 Failures attributed to equipment,test get up, or operator deficiencies shall not disqualify the product. When product failure occurs,corrective action shall be taken and samples resubmitted for qualification. ...