MCP6547-I/P Microchip Technology, MCP6547-I/P Datasheet - Page 2

• Manufacturer Part Number: MCP6547-I/P
• Description: IC COMP OPENDRN 1.6V DUAL 8-DIP
• Manufacturer: Microchip Technology
• Type: General Purposer

Specifications of MCP6547-I/P

• Output Type: CMOS, Open-Drain, Rail-to-Rail, TTL
• Package / Case: 8-DIP (0.300", 7.62mm)
• Number Of Elements: 2
• Voltage - Supply: 1.6 V ~ 5.5 V
• Mounting Type: Through Hole
• Number Of Channels: 2 Channels
• Product: Analog Comparators
• Response Time: 4 us
• Offset Voltage (max): 7 mV
• Input Bias Current (max): 1 pA
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1.6 V
• Supply Current (max): 1 uA
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: MCP6547I/P

MCP6546/7/8/9
1.0
1.1
V
Open-Drain output..................................... V
All inputs and outputs ........... V
Difference Input voltage ............................ |V
Output Short-Circuit Current .......................continuous
Current at Input Pins .........................................±2 mA
Current at Output and Supply Pins .................. ±30 mA
Storage temperature .......................... -65°C to +150°C
Maximum Junction Temperature (T
ESD protection on all pins (HBM;MM)..........4 kV;200V
DC CHARACTERISTICS
DS21714C-page 2
Electrical Specifications: Unless otherwise indicated, V
R
Power Supply
Supply Voltage
Quiescent Current per comparator
Input
Input Voltage Range
Common Mode Rejection Ratio
Common Mode Rejection Ratio
Common Mode Rejection Ratio
Power Supply Rejection Ratio
Input Offset Voltage
Input Hysteresis Voltage
Input Bias Current
Input Offset Current
Common Mode Input Impedance
Differential Input Impedance
Open-Drain Output
Output Pull-Up Voltage
High-Level Output Current
Low-Level Output Voltage
Short-Circuit Current
Output Pin Capacitance
Note 1:
DD
PU
Drift with Temperature
Drift with Temperature
Over Temperature
Drift with Temperature
- V
= 2.74 k to V
2:
3:
SS
ELECTRICAL
CHARACTERISTICS
Absolute Maximum Ratings †
Parameters
..............................................................7.0V
The input offset voltage is the center of the input-referred trip points. The input hysteresis is the difference between the
input-referred trip points.
Do not short the output above V
comparator does not function properly when V
Input bias current overtemperature is not tested for the SC-70-5 package.
PU
= V
DD
(Refer to Figure 1-3).
SS
V
V
–0.3V to V
V
J
CMRR
CMRR
CMRR
PSRR
V
HYST
HYST
V
Sym
Z
C
) ............... +150°C
V
V
OS
Z
V
V
I
HYST
I
CMR
DIFF
I
I
OS
OH
OUT
I
I
CM
SC
DD
OS
PU
Q
B
B
OL
/ T
/ T
/ T
SS
A
A
A
+ 10V. Limit the output current to Absolute Maximum Rating of 30 mA. The
SS
V
DD
DD
SS
-100
+10.5V
Min
-7.0
V
V
1.6
0.3
1.5
55
50
55
63
—
—
—
—
—
—
—
—
—
—
+0.3V
- V
DD
SS
0.3
SS
DD
PU
|
= +1.6V to +5.5V, V
10
10
< V
±1.5
Typ
±50
0.6
3.3
70
65
70
80
—
—
10
—
13
13
—
—
—
±3
±1
1
8
5
DD
||4
||2
.
† Notice: Stresses above those listed under “Maximum Rat-
ings” may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational listings of this specification is not implied. Expo-
sure to maximum rating conditions for extended periods may
affect device reliability.
PIN FUNCTION TABLE
V
V
V
V
V
V
OUT, OUTA, OUTB, OUTC,
OUTD
CS
NC
DD
SS
IN
IN
DD
SS
Max
+7.0
100
5.5
6.5
10
—
—
—
—
—
—
—
—
—
—
—
—
—
—
+, V
–, V
1
+ 0.3
+ 0.2
INA
INA
SS
+, V
–, V
Units
µV/°C T
µV/°C T
µV/°C T
= GND, T
mV
mV
mA
µA
dB
dB
dB
dB
pA
pA
pA
nA
pF
||pF
||pF
NAME
V
V
V
V
INB
INB
–, V
+, V
I
V
V
V
V
V
V
V
T
V
(Note 2)
V
I
V
OUT
OUT
A
A
A
A
DD
DD
DD
CM
CM
CM
CM
CM
DD
PU
A
INC
INC
= -40°C to +85°C, V
= -40°C to +25°C, V
= +25°C to +85°C, V
= -40°C to +85°C, V
= 25°C, V
= 5V, V
= 5V, V
= 5V, V
= 1.6V to 5.5V, V
= V
= V
= V
= 0
= V
= V
= V
= 2 mA, V
–, V
+, V
DD
SS
SS
SS
SS
SS
2003 Microchip Technology Inc.
IND
IND
(Note 1)
(Note 1)
= 5.0V (Note 2)
CM
CM
CM
– Inverting Inputs
+ Non-Inverting Inputs
IN
Conditions
PU
= -0.3V to 5.3V
= 2.5V to 5.3V
= -0.3V to 2.5V
+ = V
Positive Power Supply
Negative Power Supply
Outputs
Chip Select
Not Connected
= V
DD
PU
DD
FUNCTION
CM
CM
CM
CM
/2, V
= 10V (Note 2)
= 5V
= V
= V
= V
= V
IN
SS
SS
SS
– = V
SS
(Note 3)
SS
,