LTC1440CMS8 Linear Technology, LTC1440CMS8 Datasheet - Page 10

• Manufacturer Part Number: LTC1440CMS8
• Description: IC COMP W/REF LP SINGLE 8-MSOP
• Manufacturer: Linear Technology
• Type: with Voltage Referencer

Specifications of LTC1440CMS8

• Number Of Elements: 1
• Output Type: CMOS, TTL
• Voltage - Supply: 2 V ~ 11 V, ±1 V ~ 5.5 V
• Mounting Type: Surface Mount
• Package / Case: 8-TSSOP, 8-MSOP (0.118", 3.00mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

APPLICATIONS
LTC1440/LTC1441/LTC1442
LTC1440/LTC1441/LTC1442 are a family of micropower
comparators with built-in 1.182V reference. Features
include programmable hysteresis (LTC1440/LTC1442),
wide supply voltage range (2V to 11V) and the ability of the
reference to drive up to a 0.01µF capacitor without oscil-
lation. The comparators’ CMOS outputs can source up to
40mA and the supply current glitches, that normally occur
when switching logic states, have been eliminated.
Power Supplies
The comparator family operates from a single 2V to 11V
supply. The LTC1440 includes a separate ground for the
comparator output stage, allowing a split supply ranging
from ±1V to ±5.5V. Connecting V
will allow single supply operation. If the comparator out-
put is required to source more than 1mA, or the supply
source impedance is high, V
0.1µF capacitor.
Comparator Inputs
The comparator inputs can swing from the negative sup-
ply V
inputs can be forced 300mV below V
damage and the typical input leakage current is only
±10pA.
Comparator Outputs
The LTC1440 comparator output swings between GND
and V
LTC1441 and LTC1442 outputs swing between V
The outputs are capable of sourcing up to 40mA and
sinking up to 5mA while still maintaining microampere
quiescent currents. The output stage does not generate
crowbar switching currents during transitions which helps
minimize parasitic feedback through the supply pins.
Voltage Reference
The internal bandgap reference has a voltage of 1.182V
referenced to V
– 40°C to 85°C. It can source up to 200µA and sink up to
20µA with a 5V supply. The reference can drive a bypass
10
–
+
to within 1.3V max of the positive supply V
to assure TTL compatibility with a split supply. The
–
. The reference accuracy is 1.5% from
U
INFORMATION
U
+
should be bypassed with a
–
to GND on the LTC1440
W
–
or above V
U
+
–
without
and V
+
. The
+
.
capacitor of up to 0.01µF without oscillation and by
inserting a series resistor, capacitance values up to 100µF
can be used (Figure 1).
Figure 2 shows the resistor value required for different
capacitor values to achieve critical damping. Bypassing
the reference can help prevent false tripping of the com-
parators by preventing glitches on V
transients from disturbing the reference output voltage.
Figure 3 shows the bypassed reference output with a
square wave applied to the V
10mV of hysteresis voltage band while R1 damps the
reference response. Note that the comparator output
doesn’t trip.
Figure 2. Damping Resistance vs Bypass Capacitor Value
REFERENCE
Figure 1. Damping the Reference Output
1000
100
OUTPUT
0.1
10
0.001
1
0.01
CAPACITOR VALUE (µF)
R1
C1
+
0.1
pin. Resistors R2 and R3 set
REF
V
LTC144X
–
1440/1/2 F01
1
+
or reference load
1440/1/2 F02
10
144012fd