MAX907CSA+ Maxim Integrated Products, MAX907CSA+ Datasheet - Page 7

• Manufacturer Part Number: MAX907CSA+
• Description: IC COMPARATOR TTL DUAL HS 8-SOIC
• Manufacturer: Maxim Integrated Products
• Type: General Purposer

Specifications of MAX907CSA+

• Number Of Elements: 2
• Output Type: TTL
• Voltage - Supply: 4.5 V ~ 11 V
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (0.154", 3.90mm Width)
• Number Of Channels: 2 Channels
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Supply Current (max): 1 mA
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• Propagation Delay Time: 40 ns
• Comparator Type: High Speed
• No. Of Comparators: 2
• Response Time: 40ns
• Ic Output Type: TTL
• Supply Current: 800µA
• Supply Voltage Range: 4.5V To 5.5V
• Amplifier Case Style: SOIC
• No. Of Pins: 8
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

4) Choose the threshold voltage for V
5) Calculate R2 as follows:
1 / {[3 / (1.2
6) Verify the threshold voltages with these formulas:
7) Check the error due to input bias current (5nA). If the
Use 10nF power-supply bypass capacitors. Use 100nF
bypass capacitors when supply impedance is high,
when supply leads are long, or when excessive noise is
expected on the supply lines. Minimize signal trace
lengths to reduce stray capacitance. Minimize the
capacitive coupling between IN- and OUT. For slow-
moving input signals (rise time > 1ms) use a 1nF
capacitor between IN+ and IN-.
MAX9075 TRANSISTOR COUNT: 86
MAX9077 TRANSISTOR COUNT: 142
this example, choose V
A 1% preferred value is 64.9kΩ.
V
V
error is too large, reduce R3 and recalculate.
V
IN
IN
TH
R2 = 1 / {[V
rising:
falling:
= I
V
THR
B
(R1
✕
V
= V
100kΩ)] - 1/100kΩ - 1/10MΩ} = 67.114kΩ
THF
✕
THR
REF
R2
= V
_______________________________________________________________________________________
Board Layout and Bypassing
/ (V
✕
✕
THR
R3) / (R1 + R2 + R3) = 0.2mV
R1 (1/R1 + 1/R2 + 1/R3)
REF
THR
- (R1
✕
Chip Information
= 3V.
R1)] - 1/R1 - 1/R3} =
✕
V
CC
IN
) / R3
rising (V
THR
Single-Supply Comparators
Low-Cost, Ultra-Small, 3µA
). In
Figure 1. Adding Hysteresis
TOP VIEW
V
Pin Configurations (continued)
IN
R1
R2
OUTA
OUTA
INA+
INA+
GND
GND
INA-
INA-
1
2
4
1
2
4
3
3
V
REF
µMAX/SO
SOT23-8
MAX9077
MAX9077
GND
V
V
CC
CC
6
6
8
7
5
8
7
5
MAX9075
MAX9077
R3
V
OUTB
INB-
INB+
V
OUTB
INB-
INB+
OUT
CC
CC
7