TUA 6045-2 Infineon Technologies, TUA 6045-2 Datasheet - Page 41
![no-image](/images/manufacturer_photos/0/3/327/infineon_technologies_sml.jpg)
TUA 6045-2
Manufacturer Part Number
TUA 6045-2
Description
IC TUNER MOPLL PRTBL 48-VQFN
Manufacturer
Infineon Technologies
Series
OMNITUNE™r
Type
Tunerr
Datasheet
1.TUA_6045.pdf
(64 pages)
Specifications of TUA 6045-2
Package / Case
48-VQFN
Applications
NTSC, PAL
Mounting Type
Surface Mount
Bus Type
I2C
Maximum Frequency
1492 MHz
Minimum Frequency
1452 MHz
Mounting Style
SMD/SMT
Function
TV
Noise Figure
8 dB
Operating Supply Voltage
3.3 V, 5 V
Supply Voltage (min)
3 V
Supply Voltage (max)
5.5 V
Minimum Operating Temperature
- 20 C
Maximum Operating Temperature
+ 85 C
Packages
PG-VQFN-48
Vs (min)
3.0 V
Vs (max)
5.5 V
Icc (max)
62.0 mA
Esd Protection (max)
2.0 kV
Interfaces
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
TUA60452XT
1) Values are referred to
2) The RF frequency range is defined by the oscillator frequency range and the intermediate frequency (IF).
3) Local oscillator FM modulation resulting from I
4) (N+5) -1 MHz is defined as the input level of channel N+5, at frequency 1 MHz lower, causing 100 kHz FM
5) Impedance measured with differential 2-port measurement at input or output. Input and output pins directly
6) Limits are related to the tank circuit used in the application board. Frequency bands may be adjusted by the
7) The supply ripple susceptibility is a sideband measurement using a spectrum analyzer connected to the IF
8) This is the level of divider interferences close to the IF frequency. For example channel S3: f
9) Crystal oscillator interference means the 4 MHz sidebands caused by the crystal oscillator. The rejection has
10) The reference frequency rejection is the level of reference frequency sidebands (e.g. 62.5 kHz) related to the
11) Channel S02 beat is the interfering product of f
5.2
Table 7
1)
Data Sheet
Pin Designation
Function
I
3-Wire mode
2
C mode
unless stated otherwise.
modulation analyzer with a peak to peak detector ((P
I
are not altered. The refresh interval between each data set shall be 20 ms to 1 s.
sidebands 30 dB below the wanted carrier.
connected to measurement equipment with 50
choice of external components.
output. An unmodulated RF signal with a level of 80 dBµV is applied to the test board RF input. A sinewave
signal with a defined frequency is superposed onto the supply voltage (see
measurement" on Page
1/4 f
to be greater than 60 dB for an SAW driver output of 100 dBµV.
carrier. The rejection has to be greater than 60 dB for an SAW driver output of 100dBµV.
mechanisms are f
see Table 8 Chip Address Organization in I2C Mode on page
see Table 9 Address selection in I2C Mode on page 42
2
C messages are sent to the tuner in such a way that the tuner is addressed but the content of the PLL registers
OSC
= 39.5375 MHz. The rejection has to be greater than 60 dB for an SAW driver output of 100 dBµV.
Bus Interface
Pin Function
OSC
- 2 x f
Figure 4.2 "Application circuit for hybrid application" on Page 27
BUSMODE
bus mode
1 or open
62). The specified value is the worst case in the frequency range.
select
IF
or 2 x f
0
RFpix
- f
SDA / Data
data in/out
serial data
OSC
RFpix
.
2
strip lines.
, f
C communication is measured at the IF output using a
41
IF
+
and f
+ P
-
) / 2) and a post detection filter 20 Hz - 100 kHz. The
OSC
SCL / Clock
of channel S02, f
clock in
clock
42,
Figure 16 "Ripple susceptibility
four chip addresses
0: chip is addressed
BEAT
Revision 3.1, 2006-12-19
select, 3-W: enable
I
= 37.35 MHz. The possible
2
C: chip address
CAS / EN
TUA 6045-2
OSC
and f
TAIFUN 3
Reference
= 158.15 MHz,
IF
= 36 MHz,
1)