MAX4030E Maxim, MAX4030E Datasheet
MAX4030E
Available stocks
Related parts for MAX4030E
MAX4030E Summary of contents
Page 1
... The MAX4031E provides individual shutdown control for each of the amplifiers. The dual MAX4030E is available in 8-pin µMAX packages, and the triple MAX4031E is available in 14-pin TSSOP and SO packages. All devices are specified over the -40° ...
Page 2
... SO (derate 5.9mW/°C above +70°C)..................471mW Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability ...
Page 3
Low-Cost, 144MHz, Dual/Triple Op Amps DC ELECTRICAL CHARACTERISTICS (continued) /2, SHDN_ = 5V 0V OUT_ +25°C.) (Note 1) A PARAMETER SYMBOL Disabled Output Leakage Current ESD ...
Page 4
Low-Cost, 144MHz, Dual/Triple Op Amps with ±15kV ESD Protection ( 1.5V +2V/ VCL SMALL-SIGNAL GAIN vs. FREQUENCY 100mV OUT P ...
Page 5
Low-Cost, 144MHz, Dual/Triple Op Amps ( 1.5V +2V/ VCL OUTPUT VOLTAGE SWING vs. RESISTIVE LOAD 0.50 0.45 0.40 0.35 V 0.30 OL 0.25 0.20 0.15 0. ...
Page 6
... RF signal-pro- cessing applications. Ground-Sensing Inputs The MAX4030E/MAX4031E input stage can sense com- mon-mode voltages from ground to within 2.25V of the positive supply. Rail-to-Rail Outputs The MAX4030E/MAX4031E rail-to-rail outputs can ...
Page 7
... Do not make 90° turns; round all corners. V OUT_ Output Capacitive Loading and Stability The MAX4030E/MAX4031E are optimized for AC perfor IN_+ 150 mance and do not drive highly reactive loads, which decreases phase margin and can produce excessive ringing and oscillation. Figure 3 shows a circuit modifi- cation that uses an isolation resistor (R this problem ...
Page 8
... Capacitance and 10 Isolation Resistor The IEC 1000-4-2 standard covers ESD testing and per- formance of finished equipment; it does not specifically refer to ICs. The MAX4030E/MAX4031E enable the design of equipment that meets the highest level (level 4) of IEC 1000-4-2 without the need for additional ESD protection components ...
Page 9
Low-Cost, 144MHz, Dual/Triple Op Amps 5V TEST POINT A 75 MAX403_E V EE 200 200 Figure 7. ESD Test Circuit CHARGE CURRENT DISCHARGE LIMIT RESISTOR RESISTANCE HIGH- VOLTAGE STORAGE ...
Page 10
... Low-Cost, 144MHz, Dual/Triple Op Amps with ±15kV ESD Protection (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information www.maxim-ic.com/packages Ø 0.50±0.1 0.6±0.1 1 0.6±0.1 D TOP VIEW FRONT VIEW ...
Page 11
... Low-Cost, 144MHz, Dual/Triple Op Amps (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information www.maxim-ic.com/packages.) ______________________________________________________________________________________ with ±15kV ESD Protection Package Information (continued) PACKAGE OUTLINE, TSSOP 4.40mm BODY 1 21-0066 ...
Page 12
... A1 FRONT VIEW Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © ...