MAX4017 Maxim, MAX4017 Datasheet
MAX4017
Available stocks
Related parts for MAX4017
MAX4017 Summary of contents
Page 1
... Low-Cost, High-Speed, Single-Supply, Gain of +2 Buffers with Rail-to-Rail Outputs in SOT23 _______________General Description The MAX4014/MAX4017/MAX4019/MAX4022 are preci- sion, closed-loop, gain of +2 (or -1) buffers featuring high slew rates, high output current drive, and low dif- ferential gain and phase errors. These single-supply devices operate from +3.15V to +11V, or from ± ...
Page 2
... Lead Temperature (soldering, 10sec) .............................+300°C ∞ ground noninverting configuration OUT CC = +25°C.) (Note 1) CONDITIONS IN_+ IN_ 50Ω L Any channels for MAX4017/MAX4019/MAX4022 IN_+ (Note 2) IN_+, over input voltage range ≥ 50Ω 0.5V) ≤ V ≤ OUT +25° 20Ω ...
Page 3
... L NTSC 150Ω 10kHz 10kHz IN MAX4019, EN_ = 10MHz MAX4019 MAX4019 MAX4017/MAX4019/MAX4022 10MHz 20mVp-p OUT MAX4017/MAX4019/MAX4022 10MHz 2Vp-p OUT = +25°C. Specifications over temperature limits are guaranteed 0V +4.5V to +5.5V; for dual ±5V supply with 0V MIN ...
Page 4
... Operating Characteristics (V = + 150Ω VCL L SMALL-SIGNAL GAIN vs. FREQUENCY 100k 1M 10M 100M 1G FREQUENCY (Hz) MAX4017/19/22 CROSSTALK vs. FREQUENCY -10 -30 -50 -70 -90 -110 -130 -150 100k 1M 10M 100M 1G FREQUENCY (Hz) HARMONIC DISTORTION vs. LOAD 5MHz -10 V ...
Page 5
Low-Cost, High-Speed, Single-Supply, Gain of +2 Buffers with Rail-to-Rail Outputs in SOT23 __________________________________________Typical Operating Characteristics (V = + 150Ω VCL L POWER-SUPPLY REJECTION vs. FREQUENCY ...
Page 6
Low-Cost, High-Speed, Single-Supply, Gain of +2 Buffers with Rail-to-Rail Outputs in SOT23 __________________________________________Typical Operating Characteristics (V = + 150Ω VCL L POWER-SUPPLY CURRENT (PER AMPLIFIER) vs. POWER-SUPPLY VOLTAGE ...
Page 7
... Low-Cost, High-Speed, Single-Supply, Gain of +2 Buffers with Rail-to-Rail Outputs in SOT23 ______________________________________________________________Pin Description PIN MAX4014 MAX4017 MAX4019 SOT23-5 SO/µMAX SO QSOP — — — 1 — — — — 4 — — — — — — — ...
Page 8
... Low-Cost, High-Speed, Single-Supply, Gain of +2 Buffers with Rail-to-Rail Outputs in SOT23 _______________Detailed Description The MAX4014/MAX4017/MAX4019/MAX4022 are sin- gle-supply, rail-to-rail output, voltage-feedback, closed- loop buffers that employ current-feedback techniques to achieve 600V/µs slew rates and 200MHz band- widths. These buffers use internal 500Ω resistors to ...
Page 9
Low-Cost, High-Speed, Single-Supply, Gain of +2 Buffers with Rail-to-Rail Outputs in SOT23 20 0 -20 -40 -60 -80 -100 -120 -140 -160 0 100 200 300 V (mV ABOVE V IL Figure 2. Enable Logic-Low Input Current vs. Enable Logic- ...
Page 10
... Figure 6 shows the frequency response of the MAX4014/ MAX4017/MAX4019/MAX4022 under different capacitive loads. To drive loads with greater than 25pF of capaci- tance or to settle out some of the peaking, the output requires an isolation resistor like the one shown in 500Ω ...
Page 11
... CAPACITIVE LOAD (pF) Figure 8. Capacitive Load vs. Isolation Resistance Figure 7. Figure graph of the optimal isolation resis- tor versus load capacitance. Figure 9 shows the frequen- cy response of the MAX4014/MAX4017/MAX4019/ MAX4022 when driving capacitive loads with a 27Ω isola- tion resistor. ______________________________________________________________________________________ 200 250 Figure 9. Small-Signal Gain vs. Frequency with Load Capacitance and 27Ω ...
Page 12
... Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2001 Maxim Integrated Products V OUTA INA OUTB MAX4017 INA INB INB+ EE IN- SO/µMAX OUTA 1 ...