MAX4022 Maxim, MAX4022 Datasheet - Page 8
MAX4022
Manufacturer Part Number
MAX4022
Description
The MAX4014/MAX4017/MAX4019/MAX4022 are precision, closed-loop, gain of +2 (or -1) buffers featuring high slew rates, high output current drive, and low differential gain and phase errors
Manufacturer
Maxim
Datasheet
1.MAX4014.pdf
(12 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MAX4022CSD
Manufacturer:
LH
Quantity:
6 226
Company:
Part Number:
MAX4022EEE
Manufacturer:
MAXIM
Quantity:
14
Part Number:
MAX4022EEE
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX4022ESD
Manufacturer:
MAXIM
Quantity:
11 500
Part Number:
MAX4022ESD
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX4022ESD+T
Manufacturer:
MAXIM
Quantity:
24
Low-Cost, High-Speed, Single-Supply, Gain of +2
Buffers with Rail-to-Rail Outputs in SOT23
The MAX4014/MAX4017/MAX4019/MAX4022 are sin-
gle-supply, rail-to-rail output, voltage-feedback, closed-
loop buffers that employ current-feedback techniques
to achieve 600V/µs slew rates and 200MHz band-
widths. These buffers use internal 500Ω resistors to
provide a preset closed-loop gain of +2V/V in the non-
inverting configuration or -1V/V in the inverting configu-
ration. Excellent harmonic distortion and differential
gain/phase performance make these buffers an ideal
choice for a wide variety of video and RF signal-pro-
cessing applications.
Local feedback around the buffer’ s output stage
ensures low output impedance, which reduces gain
sensitivity to load variations. This feedback also pro-
duces demand-driven current bias to the output tran-
sistors for ±120mA drive capability, while constraining
total supply current to less than 7mA.
These devices operate from a single +3.15V to +11V
power supply or from dual supplies of ±1.575V to
±5.5V. For single-supply operation, bypass the V
to ground with a 0.1µF capacitor as close to the pin as
possible. If operating with dual supplies, bypass each
supply with a 0.1µF capacitor.
Each buffer in the MAX4014 family can be configured
for a voltage gain of +2V/V or -1V/V. For a gain of
Figure 1a. Noninverting Gain Configuration (A
8
_______________Detailed Description
*R
IN
__________Applications Information
L
R
= 2R
TIN
_______________________________________________________________________________________
IN+
IN-
500Ω
500Ω
Selecting Gain Configuration
MAX40_ _
OUT
*R
Power Supplies
V
= +2V/V)
CC
*R
OUT
pin
+2V/V, ground the inverting terminal. Use the noninvert-
ing terminal as the signal input of the buffer (Figure 1a).
Grounding the noninverting terminal and using the
inverting terminal as the signal input configures the
buffer for a gain of -1V/V (Figure 1b).
Since the inverting input exhibits a 500Ω input imped-
ance, terminate the input with a 56Ω resistor when the
device is configured for an inverting gain in 50Ω appli-
cations (terminate with 88Ω in 75Ω applications).
Terminate the input with a 49.9Ω resistor in the nonin-
verting case. Output terminating resistors should direct-
ly match cable impedances in either configuration.
Maxim recommends using microstrip and stripline tech-
niques to obtain full bandwidth. To ensure that the PC
board does not degrade the buffer’s performance, design
it for a frequency greater than 1GHz. Pay careful attention
to inputs and outputs to avoid large parasitic capaci-
tance. Whether or not you use a constant-impedance
board, observe the following guidelines when designing
the board:
• Don’t use wire-wrapped boards. They are too inductive.
• Don’t use IC sockets. They increase parasitic capac-
• Use surface-mount instead of through-hole compon-
• Use a PC board with at least two layers; it should be
• Keep signal lines as short and as straight as possi-
Figure 1b. Inverting Gain Configuration (A
IN
R
*R
R
TIN
itance and inductance.
ents for better high-frequency performance.
as free from voids as possible.
ble. Do not make 90° turns; round all corners.
S
L
= 2R
IN+
IN-
500Ω
500Ω
MAX40_ _
OUT
Layout Techniques
*R
V
= -1V/V)
*R
OUT